Veröffentlichungen 2014

J. R. Kornmeier, J. Šaroun, J. Gibmeier, M. Hofmann: Neutron residual strain surface scans - Experimental results and Monte Carlo simulations, Materials Science Forum Vols. 768-769 (2014), 52-59
E. Obelode, J. Gibmeier: Influence of the interfacial roughness on residual stress analysis of thick film systems by incremental hole drilling, Materials Science Forum Vols. 768-769 (2014,) 136-143
J. Gibmeier, E. Obelode, J. Altenkirch, A. Kromm, T. Kannengießer: Residual stress in steel fusion welds joined using low transformation temperature (LTT) filler material, Materials Science Forum Vols. 768-769 (2014), 620-627
S. Roy, J. Gibmeier, V. Kostov, K. A. Weidenmann, A. Nagel, A. Wanner: Load partitioning study in a 3D interpenetrating AlSi12/Al2O3 metal/ceramic composite, Materials Science Forum Vol. 772 (2014), 103-107, doi:10.4028/www.scientific.net/MSF.772.103
V. Kostov, J. Gibmeier, A. Wanner: Laser surface hardening of steel: Effect of process atmosphere on the microstructure and residual stresses, Materials Science Forum Vol. 772 (2014), 149-153
J. Rebelo Kornmeier, A. Ostermann, M. Hofmann, J. Gibmeier: Optimization of a multi-channel parabolic guide for the material science diffractometer STRESS-SPEC at FRM II, Nuclear Instruments and Physics Research A 736 (2014), 150–155
J. Kümmel, J. Gibmeier, E. Müller, R. Schneider, V. Schulze, A. Wanner: Detailed analysis of microstructure of intentionally formed built-up edges for improving wear behaviour in dry metal cutting process of steel, Wear, vol. 311 (2014), issues 1-2, 21-30,
M. Merzkirch, A. Reeb, V. Schulze, K. A. Weidenmann: Cyclic deformation and damage behaviour of the spring steel wire reinforced aluminum alloy EN AW-6082, Journal of Material Science 49 (2014), 2187–2203, DOI 10.1007/s10853-013-7913-5
S. Dietrich, K. Weidenmann, P. Elsner: 3D tomographic characterization of sandwich structures, NDT & E International; Volume 62, March (2014), 77–84
F. Lienert, J. Hoffmeister and V. Schulze: Residual stress depth distribution after piezo peening of quenched and tempered, AISI 4140, Material Science Forum Vols. 768-769 (2014) 526-533 10.4028/www.scientific.net/MSF.768-769.526
R. Weingärtner, J. Hoffmeister, V. Schulze: Generation and determination of compressive residual stresses of short penetration depths, Materials Science Forum Vols. 768-769 (2014), 580-586
doi:10.4028/www.scientific.net/MSF.768-769.580
M. Merzkirch, M. Meissner, V. Schulze, K. A. Weidenmann: Tensile behaviour of spring steel wire reinforced EN AW-6082, Journal of Composite Materials (2014), published onl. 2014, DOI: 10.1177/0021998313517581
A. Malecki, G. Potdevin, T. Biernath, E. Eggl, K. Willer, T. Lasser, J. Maisenbacher, J. Gibmeier, A. Wanner, F. Pfeiffer: X-ray tensor tomography, EPL, 105 (2014) 38002,(doi: 10.1209/0295-5075/105/38002)
C. Hochmuth, D. Schliephake, R. Völkl, M. Heilmaier, U. Glatzel: Influence of zirconium content on microstructure and creep properties of Mo-9Si-8B alloys, Intermetallics 48 (2014), 3-9
M. Krüger, P. Jain, K.S. Kumar, M. Heilmaier:  Correlation between microstructure and properties of fine grained Mo-Mo3Si-Mo5SiB2 alloys, Intermetallics 48 (2014), 10-18
A. Lange, R. Braun, M. Heilmaier: Oxidation behavior of magnetron sputtered double layer coatings containing molybdenum, silicon and boron, Intermetallics 48 (2ß14), 19-27
B. Gorr, L. Wang, S. Burk, M. Azim, S. Majumdar, H.-J. Christ, D. Mukherji, J. Rösler, D. Schliephake, M. Heilmaier: High-temperature oxidation behavior of Mo-Si-B-based and Co-Re-Cr-based alloys, Intermetallics 48 (2014), 34-43
M. Schwenk, J. Hoffmeister, V. Schulze: Experimentally validated residual stresses and distortion prediction for dual frequency induction hardening, International Journal of Applied Electromagnetics and Mechanics Bd. 44 (2014), Nr. 2, S. 127–135, DOI: 10.3233/JAE-141752
E. Held, J. Gibmeier: Residual Stress Analysis of Thick Film Systems by the Incremental Hole-Drilling Method - Influence of Interlayers and Interfacial Roughness, HTM Journal of Heat Treatment and Materials 69 (2014) 2, S. 71-79, (DOI: 10.3139/105.110216)
J. Gibmeier, E. Held, J. Altenkirch, A. Kromm, Th. Kannengiesser, Th. Buslaps: Real time monitoring of phase transformation and strain evolution in LTT weld filler material using EDXRD, Journal of Materials Processing Technology 214 (2014), S. 2739–2747 (DOI: 10.1016/j.jmatprotec.2014.06.008)
E. Held, S. Schuster, J. Gibmeier: Incremental hole-drilling method vs. thin components: a simple correction approach, Advanced Materials Research Vol. 996 (2014), S. 283-288 (doi: 10.4028/www.scientific.net/AMR.996.283)
V. Kostov, J. Gibmeier, K. Lichtenberg and A. Wanner: Effect of Preloading on Local Residual Stresses Induced by Laser Surface Hardening of Steel, Advanced Materials Research Vol. 996 (2014), S. 562-567 (doi: 10.4028/www.scientific.net/AMR.996.562)
J. Kümmel, J. Gibmeier, V. Schulze, A. Wanner:
Effect of built-up edge formation on residual stresses induced by dry cutting of normalized steel, Advanced Materials Research Vol. 996 (2014), S. 603-608 (doi: 10.4028/www.scientific.net/AMR.996.603)
A.Reeb, L. Schweizer, K.A. Weidenmann, V.Schulze: Characterization of unreinforced and steel wire reinforced magnesium alloy AZ31 under mechanical-corrosive loading, Procedia CIRP, 18( 2014 ), 114 – 119 doi: 10.1016/j.procir.2014.06.117

M. Merzkirch, Ch. Blümel, R. Rössler, K. G. Schell, E. C. Bucharsky, K. A. Weidenmann:
Manufacturing and Characterization of Interpenetrating SiC Lightweight Composites, Procedia CIRP, International Conference on Manufacture of Lightweight Components – ManuLight2014, 18, 102 – 107, 2014 doi: 10.1016/j.procir.2014.06.115

J. Kümmel, A. Ohl, E. Müller, R. Schneider, J. Gibmeier: Detaillierte Mikrostrukturanalyse stark verformter ferritisch-perlitischer Gefüge, Sonderbände der Praktischen Metallographie 46,(2014), 95-100, ISBN 978-3-88355-403-7
J. Maisenbacher, J. Gibmeier, K. Klimscha, T. Fischer, P. Staron: Locally resolved stress and strain analysis of sinter-joined micro valves using synchrotron X-ray diffraction and conical slit apertures, Microsystem Technologies, DOI 10.1007/s00542-014-2285-6 (2014)
S. Schuster, J. Gibmeier: Residual Stress Analysis of Strongly Textured Materials by Means of the Incremental Hole-Drilling Method – Survey on the Application Limits, Materials Testing 2014: Vol. 56, No. 11-12, S. 915-922 DOI 10.3139/120.110651
M. Merzkirch, M. Meissner, V. Schulze, K. A. Weidenmann: Numerical analysis to study the tensile behaviour of a spring-steel-wire-reinforced aluminium alloy metal matrix composite, Journal of Composite Materials, 2014, DOI: 10.1177/0021998314553044
S. Guth, S. Doll, K.-H. Lang: Lifetime, Cyclic Deformation and Damage Behaviour of MAR-M247 LC under Thermo-Mechanical Fatigue Loading with 0°, 180°, -90° and + 90° Phase Shift between Strain and Temperature, Procedia Engineering 74 (2014) p. 269 – 272, doi:10.1016/j.proeng.2014.06.260
V. Walter, K.A. Weidenmann, V. Schulze: A Comparison of FSW, BHLW and TIG Joints for AL-Si-Mg alloy (EN AW-6082 T6), International Conference on Manufactur of Lightweight Components – Manu Light 2014, doi:10.1016/j.procir.2014.06.118
V. Kostov, J. Gibmeier, A. Wanner: Time-Resolved X-Ray Diffraction Stress Analysis during Laser Surface Hardening of Steel - Impact of the maximum process temperature, HTM Journal of Heat Treatment and Materials, Vol. 69, No. 6 (2014), pp. 360-367, doi: 10.3139/105.110241
F. Gang, M. Heilmaier: Influence of Directional Solidification on the Creep Properties of a Binary NbSi Eutectic Alloy, JOM Vol. 66, No.9 (2014), S. 1908-1913
T. Adams, G. Brandl, A. Chacon, J.N. Wagner, M. Rahn, S. Mühlbauer, R. Georgii, C. Pfleiderer, P. Böni: Versatile module for experiments with focussing neutron guides, Applied Physics Letters 105(12), 2014, 123505
J.N. Wagner, M. Hofmann, R. Wimpory, C. Krempaszky, M. Stockinger: Microstructure and temperature dependence of intergranular strains on diffractometric macroscopic residual stress analysis, Materials Science and Engineering A 618, 2014, 271–279
P. Schloth, J.N. Wagner, J.L. Fife, A. Menzel, J.-M. Drezet, H. Van Swygenhoven: Early precipitation during cooling of an Al-Zn-Mg-Cu alloy revealed by in situ small angle X-ray scattering, Applied Physics Letters 105(10), 2014, 101908
N. Martin, J.N. Wagner, M. Dogú, C. Fuchs, L. Kredler, P. Böni, W. Häussler: Neutron Resonance Spin Flippers: Static Coils Manufactured by Electrical Discharge Machining, Review of Scientific Instruments 85(7), 2014, 073902
C. Seemüller, T. Hartwig, M. Mulser, N. Adkins, M. Wickins, M. Heilmaier: Influence of Powder Metallurgical Processing Routes on Phase Formations in a Multicomponent NbSi-Alloy, JOM Vol. 66, No.9 (2014), 1900-1907
D. Schliephake, M. A. Azim, K. v. Klinski-Wetzel, B. Gorr, H.-J. Christ, H. Bei, E. P. George, M. Heilmaier: High-Temperature Creep and Oxidation Behavior of Mo-Si-B Alloys with High Ti Contents, Metall. Mater. Trans. 45A (2014), 1102-1111
J.H. Schneibel und M. Heilmaier: Hall-Petch Breakdown at Elevated Temperatures, Mater. Trans. JIM 55 (2014), 44-51
S. Dietrich, M. Koch, P. Elsner, K. Weidenmann: Measurement of Sub-Surface Core Damage in Sandwich Structures Using In-situ Hertzian Indentation During X-ray Computed Tomography, Exp Mech 54 (2014), pp. 1385–1393, DOI: 10.1007/s11340-014-9902-2
B. Kaufmann, H. Autenrieth, J. Hoffmeister, V. Schulze: Investigation on Short Time Tempering by Induction Heating of the low alloyed AISI4140 steel, Arbeitsgemeinschaft Wärmebehandlung und Werkstofftechnik e.V (Ed.), Proceedings European Conference on Heat Treatment and 21st IFHTSE Congress (2014)
F. Lienert, J. Hoffmeister, A. Erz, V. Schulze: Influence of Piezo Peening on the Fatigue Strength of quenched and tempered AISI 4140, Proceedings of ICSP12 (2014)
F. Lienert, J. Hoffmeister, V. Schulze: Changes in surface layer after Piezo Peening of quenched and tempered AISI 4140, Proceedings of ICSP12 (2104)

R. Sonntag, J. Reinders, J. Gibmeier, S. Jaeger, J. P. Kretzer: Ti-6Al-4V fatigue strength after shot peening: The role of a corrosive environment, ASTM Special Technical Publication 1559 STP (2014) pp. 98-108, DOI: 10.1520/STP155920120151

 

Veröffentlichungen 2013

C. Seemüller, M. Heilmaier, T. Haenschke, H. Bei, A. Dlouhy, E.P. George:
Influence of fiber alignment on creep in directionally solidified Nial-10Mo in-situ composites
Intermetallics 35 (2013);110-115
S. Roy, K. G. Schell, E. C. Bucharsky, K. A. Weidenmann, A. Wanner, and M.J. Hoffmann:
Characterization of Elastic Properties in Porous Silicon Carbide Preforms Fabricated Using Polymer Waxes as Pore Formers
J. Am. Ceram. Soc., 1–7 (2013), DOI: 10.1111/jace.12341
J. Kümmel, K. Poser, F. Zanger, J. Michna, and V. Schulze:
Surface Layer States of Worn Uncoated and TiN-Coated WC/Co-Cemented Carbide Cutting Tools after Dry Plain Turning of Carbon Steel
Hindawi Publishing Corporation Advances in Tribology Volume (2013), Article ID 519686, 10 pages
A. Wanner, R. Joos, A. Harnischmacher, K.-H. Lang:
Schädigung und Lebensdauer von Aluminium-Gusslegierungen für thermisch-mechanisch hochbeanspruchte Motorbauteile
Abschlussbericht über das Vorhaben Nr. 987 (2013), (AIF-Nr. 15846 N/1) Heft R562
S. Majumdar, A.Kumar, D.Schliephake, H.-J.Christ, X.Jiang, M.Heilmaier:
Microstructural and micro-mechanical properties of Mo–Si–B alloyed with Y and La
Materials Science&EngineeringA573 (2013), 257–263
M. Schwenk, B. Kaufmann, J. Hoffmeister and V. Schulze:
Modelling of strain rate and temperature dependent flow stresses of supercooled austenite for AISI 4140
Materials Science Forum Vol. 762 (2013), 122-127 © (2013) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/MSF.762.122S.
S. Majumdar, D. Schliephake, B. Gorr, H.-J. Christ, M. Heilmaier:
Effect of Yttrium Alloying on Intermediate to High-Temperature Oxidation Behavior of Mo-Si-B Alloys
Metallurgical and Materials Transactions A (2013), ISSN 1073-5623 Volume 44 Number 5 Metall and Mat Trans A  44:2243-2257 DOI 10.1007/s11661-012-1589-3
M. Schwenk, J. Hoffmeister , V. Schulze:
Experimental Determination of Process Parameters and Material Data for Numerical Modeling of Induction Hardening
Journal of Materials Engineering and Performance (2013), ISSN 1059-9495 J. of Materi Eng nd Perform DOI 10.1007/s11665-013-0566-3
P. Beneš, Dr.-Ing. J. Hoffmeister, Prof. Dr.-Ing V. Schulze, Dr.-Ing. M. Selten:
Finite-Elemente-Analyse des Prozesses Profil-Querwalzen zur Beschreibung des Materialfließens und des Versagensmechanismus im Verzahnungsinneren
Forschungsvereinigung Antriebstechnik e. V. (FVA), GETPRO 4. Kongress zur Getriebeproduktion, 5. und 6. März 2013 in Würzburg, Band I, 5. März 2013, Band II, 6. März 2013
M. Schwenk, M. Fisk, T. Cordell, J. Hoffmeister, V. Schulze and L.-E. Lindgren:
Process Simulation of Single and Dual Frequency Induction Surface Hardening Considering Magnetic Nonlinearity
Materials Performance & Characterization Special Issue on ThermalProcess Modeling, Simulation, and Optimization (2013), 165-184
C. Seemüller, M. Heilmaier, T. Hartwig, M. Mulser, N. Adkins, and M. Wickins:
Influence of microstructure and processing on mechanical properties of advanced Nb-silicide alloys
Mater. Res. Soc. Symp. Proc. (2013), 1516
D. Janda, H. Fietzek, M. Galetz, M. Heilmaier:
The effect of micro-alloying with Zr and Nb on the oxidation behavior of Fe3Al and FeAl alloys
Intermetallics Bd. 41 (2013), S. 51–57 DOI: 10.1016/j.intermet.2013.04.016
K. v. Klinski-Wetzel, C. Kowanda, T. Rettenmaier, M. Heilmaier, V. Hinrichsen, F.E.H. Mueller
Microstructural features of switched Cu-Cr surface melt layers
18th Plansee Seminar (2013)
M. Merzkirch, V. Schulze, K. A. Weidenmann
Lifetime behaviour of unidirectionally wire reinforced lightweight metal matrix composites
International Journal of Fatigue (2013), 56, 60-68
J. Kümmel,  J. Gibmeier, E. Müller, R. Schneider, V. Schulze, A. Wanner
Effect of built-up edges and transfer layers on the wear state during dry cutting
of steel with cemented carbide tools
Proceedings zum WTC V (2013),ISBN Nummer 978-88-90818509

S. Guth, A. Korinth, K.-H. Lang
Lifetime, cyclic deformation and damage behaviour of NiCr22Co12Mo9 under TMF-loadings with various phasing of strain and temperature
Seventh international conference on low cycle fatigue, Aachen, (2013), ISBN 978-3-9814516-2-7, 171-176

P.Nusskern, J. Hoffmeister, V.Schulze
Simulation des Einsatzhärtens gradiert poröser Bauteile: Materialmodellierung
HTM J. Heat Treatment Mat. 68, (2013) 6, 1-9
P.Nusskern, J. Hoffmeister, V.Schulze
Simulation of the manufacturing process of case-hardened powder metallurgical components: carburizing simulation
Adv. Eng. Mater., (2013), 10.1002/adem.201300101
P. Schäfers, P. Nusskern, A. Ohl, J. Hoffmeister und V. Schulze
Bildanalytische Bestimmung von Formfaktoren in gradiert porösen Randschichten pulvermetallurgischer Bauteile
Sonderbände der Praktischen Metallographie 45, (2013), 195-200, ISBN978-3-88355-398-6
M. Krüger, D. Schliephake, P. Jain, K.S. Kumar, G. Schumacher & M. Heilmaier:
Effects of Zr Additions on the Microstructure and the Mechanical Behavior of PM Mo-Si-B Alloys
JOM (2013) The Journal of The Minerals, Metals & Materials Society (TMS) Volume 65 S. 301-306
S. Majumdar, S. Burk, D. Schliephake, M. Krüger, H.-J. Christ, M. Heilmaier:
A Study on Effect of Reactive and Rare Earth Element Additions on the Oxidation Behavior of Mo-Si-B System, Oxid. Met. 80 (2013), 219-230
M. A. Azim, S. Burk, B. Gorr, H.-J. Christ, D. Schliephake, M. Heilmaier, R. Bornemann, P. Haring Bolívar:
Effect of Ti (Macro-) alloying on the High-Temperature Oxidation Behavior of Ternary Mo-Si-B Alloys at 820-1300 °C, Oxid. Met. 80 (2013), 231-242
J.Maisenbacher, D.Buqezi-Ahmeti, J.Gibmeier, J.Donges, T.Hanemann:
Ortsaufgelöste Eigenspannungsanalyse an Mikroverbundgussproben
Tagungsband Kolloquium Mikroproduktion, (2013), B12, ISBN 978-3-8440-2243-8 B12
E. Obelode, J. Gibmeier:
Residual Stress Analysis on Thick Film Systems by the Incremental Hole-Drilling Method – Simulation and Experimental Results
Experimental Mechanics (2013), Vol. 53, S. 965-976
Y. Sinchuk, S. Roy, J. Gibmeier, R. Piat, A. Wanner:
Numerical study of internal load transfer in metal/ceramic composites based on freeze-cast ceramic preforms and experimental validation
Materials Science and Engineering Vol. A585, (2013), 10–16
E. Held, H. Ohl, J. Gibmeier, J. Dixneit, A.Kromm, T. Kannengießer:
Mikrostruktur- und Härteentwicklung in Schweißnähten mit neuartigen LTT-Schweißzusatzwerkstoffen
Praktische Metallgraphie Sonderband 45, (2013), 297-302
A.Reeb, M. Gottschalk, K.A. Weidenmann, V. Schulze:
Rissausbreitungsverhalten von federstahldrahtverstaerktem EN AW-6082 unter mechanisch-korrosiver Beanspruchung
Tagungsband zum 19. Symposium Verbundwerkstoffe und Werkstoffverbunde (2013), 112-120
S. Dietrich, K. Weidenmann, P. Elsner:
Computertomographie in der Charakterisierung von Sandwichverbunden: Automatisierte Bildanalyse in Prüfung und Berechnung sinusoidaler Sandwichstrukturen
19. Symposium Verbundwerkstoffe und Werkstoffverbunde, Juni (2013), Tagungsband S. 916-925
R. Sonntag, J. Reinders, J. Gibmeier, J. P. Kretzer
Fatigue strengthening of an orthopedic Ti6Al4V alloy: what is the potential of a final shot peening process? (Book Chapter 4)
J. Paulo Davim (ed): Biomaterials and medical tribology, Woodhead Publishing Series in Biomaterials (2013), (ISBN 978-0-85709-017-1), S. 217-238

Veröffentlichungen 2012

J. Hoffmeister, V. Schulze, R. Hessert , G. Koenig:
Residual Stresses under quasi-static and cyclic loading in shot peened Inconel 718
International Journal of Materials Research - Zeitschrift für Metallkunde Vol. 103, (2012), 66-72

P. Nusskern, J. Hoffmeister, V. Schulze:
Austenite-Bainite transformation kinetic model for the powdermetallurgical steel Astaloy 85 Mo
Materials Science Forum Vols. 706-709 (2012), 1485-1490

S. Roy, J. Gibmeier, K.A. Weidenmann, A. Wanner:
Mechanical properties of innovative metal/ceramic composites based on freeze-cast ceramic preforms
Th. Böllinghaus, J. Lexow, T. Kishi, M. Kitagawa (Eds.): Materials Challenges and Testing for Supply of Energy and Resources, Part 3, (2012),213-220, Springer, Heidelberg

A. Ohl, J. Kümmel, K. Poser, V. Schulze, A. Wanner:
Metallographische Untersuchung von Randschichten bei der Zerspanung von normalisierten C45E Stahl mit Hartmetallwerkzeugen
Prakt. Met. Sonderband 44 (2012), 319-324

S. Dietrich, J.-M. Gebert, G. Stasiuk, A. Wanner, K.A. Weidenmann, O. Deutschmann, I. Tsukrov, R. Piat:
Microstructure characterization of CVI-densified carbon/carbon composites with various fiber distributions
Composites Science and Technology 72 (2012) S. 1892-1900

V. Kostov, J. Gibmeier, F. Wilde, P. Staron, R. Rössler et al.:
Fast in situ phase and stress analysis during laser surface treatment: A synchrotron x-ray diffraction approach
AIP Review of Scientific Instruments 83, 115101; 1-11 (2012), doi: 10.1063/1.4764532

M. Schwenk, B. Kaufmann, J. Hoffmeister, V. Schulze:
Residual Stress Prediction for Dual Frequency Induction Hardening considering Transformation Plasticity during Austenitization
ASM International; Quenching Control and Distortions, (2012), September 9-13;  45-56

S. Roy, K.G. Schell, E.C Bucharsky, P. Hettlich, S. Dietrich, K.A. Weidenmann, A. Wanner, M.J. Hoffmann:
Processing and Elastic Property Characterization of Porous SiC Preform for Interpenetrating Metal/Ceramic Composites
J. Am Ceram. Soc., 95 (2012), S. 3078-3083

S. Roy, J. Gibmeier, V. Kostov, K.A. Weidenmann, A. Nagel, A. Wanner:
Internal load transfer and damage evolition in a 3D interpenetrating metal/ceramic composite
Materials Science and Engineering A 551 (2012), 272-279

B. Thoma, K.A. Weidenmann, F. Henning:
Chemical-Stitching as a promising approach for automated preforming of textiles
Zeitschrift Kunststofftechnik 8, Carl Hanser Verlag, (2012), 491-514

S. Roy, K.G. Schell, E.C. Bucharsky, P. Hettich, S. Dietrich, K.A. Weidenmann, A. Wanner, M.J. Hoffmann:
Processing and non-destructive characterisation of porous silicone carbide preforms for metall/ceramic composite fabrication

J. Rögner, M. Müller, J. Maisenbacher, K.-H. Lang, O. Kraft, A. Wanner, V. Schulze:
Prozess-Gefüge-Eigenschaftsbeziehungen urgeformter Mikroproben aus Siliziumnitrid

J. Kümmel, K. Poser, F. Zanger, J. Michna, V. Schulze:
Surface Layer States of Worn Uncoated and TiN-Coated WC/Co-Cemented Carbide Cutting Tools after Dry Plain Turning of Carbon Steel
Hindawi Publishing Corp., Andvances in Tribology, Vol. 2013, S 1-10

C. Wörner, K.-H. Lang:
Fretting Fatigue Failure of Engineering Ceramics
D. Singh, J. Salem, M. Halbig and S. Mathur (eds.): Mechanical Properties and Performance of Engineering Ceramics and Composites VII, John Wiley & Sons, Inc., Hoboken, NJ, USA. (2012), 125-131 doi: 10.1002/9781118217467.ch12

R. Weingärtner, J. Hoffmeister, V. Schulze:
Generation and determination of compressive residual stresses of short penetration depths
Proceedings of ICSR 9 eine Veröffentlichung an „Materials Science Forum“

F. Lienert, J. Hoffmeister, V. Schulze:
Residual stress depth distribution after piezo peening of quenched and tempered AISI 4140
Proceedings of ICSR 9 eine Veröffentlichung in „Materials Science Forum“

D. Gelmedin, K.-H. Lang, J.C. Newman:
Prediction of Fatigue Lives of MAR-M247 LC Based on the Crack Closure Concept
Adv. Eng. Mater., 14, (2012), 848–852. DOI: 10.1002/adem.201100194

D. Gelmedin, K.-H. Lang:
Failure Behaviour of the Superalloy MAR-M247 LC under LCF, HCF and combined LCF/HCF loading
Int. J. Mat. Res., Vol. 103, No. 1, (2012), 97-105. DOI: 10.3139/146.110633

P. Groche; M. Engels; M. Steitz:
Potential of mechanical surface treatment for mould and die production
INTERNATIONAL JOURNAL OF MATERIALS RESEARCH Volume: 103 Issue: 6 Pages: 783-789 DOI: 10.3139/146.110778 Published: JUN 2012

D. Stancheva, K. Moch, T. Strauß, J. Hoffmeister, V. Schulze:
Relaxation of residual stresses induced by soft machining and generation of distortion during the heating step of a case hardening treatment
KIT-Report-Nr. KIT-SR 7611, (2012) Seite 37-42,

P. Nusskern, J. Hoffmeister V. Schulze:
Case hardening simulation of surface compacted, graded porous Astaloy 85 Mo components
Quenching Control and Distortion, September 9–13, 2012, Chicago, Illinois, USA Proceedings from the 6th International Quencing and Control of Distortion Conference Including the 4th International Distortion Engineering Conference, D. Scott MacKenzie, editor

A. Reeb, A. Ohl, K. Poser, T. Kloppenbourg, A. Brosius, A.E. Tekkaya, K.A. Weidenmann:
Preparation and Etching Methods for a light-Optical Microscopy Analysis of Extrusion Seams and Microstructural Contrasting for aluminium Alloys EN AW-6063 and EN AW-6082
Pract. Metallogr. 49 (2012), [10], 612-622,

V. Schulze, H. Meier, T. Strauß, J. Gibmeier:
High speed broaching of case hardening steel SAE 5120
Proceedings of 5th CIRP International Conference on High Performance Cutting, 2012

V. Schulze, J. Osterried, T. Strauß, F. Zanger:
Analysis of surface layer characteristics for sequential cutting operations

T. Strauß, H. Meier, J. Gibmeier, V. Schulze , A. Wanner:
Local residual stress distribution at the tooth root surface of a broached steel component
Materials Science Forum Vols. 706-709 (2012), 1731-1736

M. Müller, F. A. Çetinel, J. Rögner, W. Bauer, R. Knitter:
Surface state defining factors as key to the strength of ceramic micro parts
Microsyst Technol (2013) 19:555–561

D. Mukherji, J. Rösler, M. Krüger, M. Heilmaier, M.-C. Bölitz, R. Völkl, U. Glatzel, L. Szentmiklosie:
The effects of boron addition on the microstructure and mechanical properties of Co–Re-based high-temperature alloys
Scripta Materialia 66 (2012) 60–63

S. Burk, B. Gorr, H.-J. Christ, D. Schliephake, M. Heilmaier, Chr. Hochmuth, U. Glatzel:
High-temperature oxidation behaviour of a single-phase (Mo,Ti)5Si3 (Mo–Si–Ti) alloy
Scripta Materialia 66 (2012) 223–226

P. Schloth, M.A. Weisser, H. Van Swygenhoven, S. Van Petegem, P. Susila, P. Schloth, M.A. Weisser, H. Van Swygenhoven, S. Van Petegem, P. Susila, V. Subramanya Sarma, B.S. Murty, S. Lauterbach, M. Heilmaier
Two strain-hardening mechanisms in nanocrystalline austenitic steel: An in situ synchrotron X-ray diffraction study
Scripta Materialia 66 (2012) 690–693

T. Shanmugasundaram, M. Heilmaier, B.S. Murty, V. Subramanya Sarma:
On the estimation of true Hall-Petch constants and their role on the superposition law exponent in Al alloys
Adv. Eng. Mater. 14 (2012), 892-89

K. von Klinski-Wetzel; C. Kowanda; M. Boning; M. Heilmaier; F.E.H. Muller:
Parameters influencing the electrical conductivity of CuCr alloys
25th International Symposium on Discharges and Electrical Insulation in Vacuum (2012) 392 – 395

M. Schwane, T. Kloppenborg, A. Reeb, N. Ben Khalifa, A. Brosius, K.A. Weidenmann, A.E. Tekkaya:
Numerical approach for the evaluation of seam welding criteria in extrusion processes
Key Engineering Materials Vols. 504 -506 , (2012), 517 – 522

P. Beneš, J. Hoffmeister, V. Schulze, A. Bechle:
Finite-element-analysis of the forming process cross rolling with the aim of exploring the material flow and the damage degree in work pieces“
MSE in Darmstadt

D. Buqezi-Ahmeti, J. Maisenbacher, J. Gibmeier, T. Hanemann:
Metal-ceramic-composite casting of complex micro components
Microsystem Technologies (2012), DOI 10.1007/s00542-012-1624-8

J. Altenkirch, J. Gibmeier, Th. Buslaps and V. Honkimäki:
EDXRD for real time observation of a gas tungsten arc welding process
Materials Science Forum (2012), Vols. 706-709, 1655-1660

Veröffentlichungen 2011

S. Roy, O. Stoll, K. Weidenmann, A. Nagel, A. Wanner:
Analysis of the elastic properties of an interpenetrating AlSi12-Al2O3 composite using ultrasound phase spectroscopy
Composites Science and Technology 71 (2011), 962-968

S. Roy, A. Wanner, T. Beck, T. Studnitzky, G. Stephani:
Mechanical properties of cellular solids produced from hollow stainless steel spheres
Journal of Materials Science (2011)46, 5519 - 5526

V. Kostov, J. Gibmeier, A. Wanner:
Local residual stress distributions induced by repeated austenite-martensite transformation via laser surface hardening of steel AlSl 4140
Materials Science Forum Vol. 681 (2011), 321-326

T. Kloppenborg, A. Reeb, M. Merzkirch, K. Weidenmann, A. Brosius, A.E. Tekkaya:
Effiziente Strangpresssimulation für industrielle Anwendungen
In: Fortschr. Ber. VDI Reihe 2 Nr. 678, VDI-Verlag Düsseldorf, 2011, 457-466, ISBN 978-3-18-367802-0

J. Altenkirch, J. Gibmeier, A. Kromm, Th. Kannengiesser, Th. Nitschke-Pagel, M. Hofmann:
In situ study of structural integrity of low transformation temperature (LTT)-welds
Materials Science and Engineering A 528 (2011), 5566 - 5575

A. Kromm, T. Kannengiesser, J. Altenkirch, J. Gibmeier:
Residual Stresses in Multilayer Welds with Different Martensitic Transformation Temperatures Analyzed by High-Energy Synchrotron Diffraction
Materials Science Forum Vol. 681 (2011), 37 - 42

J. Kornmeier, J. Gibmeier, M. Hofmann, R.C. Wimpory:
Neutron surface residual stress scanning using optimisation of a Si bent perfect crystal monochromator for minimising spurious strains
Materials Science Forum Vol. 681 (2011), 399 - 404

J. Gibmeier, P. Maier, C. Fleck:
Strain Evolution during Mechanical Loading of the Magnesium Base Alloy LAE442 Studied by means of High Energy Synchrotron Diffraction
Materials Science Forum Vol. 681 (2011), 437-442

S. Fünfschilling, T. Fett, M.J. Hoffmann, R. Oberacker, T. Schwind, J. Wippler, T. Böhlke, H. Özcoban, G.A. Schneider, P.F. Becher, J.J. Kruzic:
Mechanisms of toughening in silicon nitrides: The roles of crack bridging and microstructure
Acta Materialia 59 (2011), 3978 - 3989

M. Merzkirch, A. Reeb, K. Weidenmann, V. Schulze:
Charakterisierung des Verformungs- und Schädigungsverhaltens unidirektional drahtverstärkter Aluminium- und Magnesiummatrixverbunde unter Zug- und Druckbeanspruchung
Proceedings of the 18 DGM Verbundwerkstoffe Symposium: Verbundwerkstoffe und Werkstoffverbunde, Chemnitz (2011), 103-108

B. Drach, I. Tsukrov, T. Gross, S. Dietrich, K. Weidenmann, R. Piat, T. Böhlke:
Numerical modeling of carbon/carbon composites with nanotextured matrix and 3D pores of irregular shapes
International Journal of Solids and Structures, IJSS-D-10-00703R1

R. Piat, G. Stasiuk, T. Böhlke, J.-M. Gebert, S. Dietrich, A. Wanner, I. Tsukrov, O. Deutschmann, G. Todd:
Influence of the preform architecture on the effective elastic material properties of carbon/carbon composites
Conference Proceeding ECCM 2010

S. Roy, J.-M. Gebert, K.A. Weidenmann, A. Wanner:
Complete stiffness characterization of interpenetrating metal/ceramic composites using a combination of ultrasonic techniques
Materials Science and Engineering  A 528 (2011), 8226-8235

K.A. Weidenmann, R. Tavangar, L. Weber:
Influence of Thermal Cycling on the Mechanical Properties of Al/Diamond Composites
Proceedings of the 18 DGM Verbundwerkstoffe Symposium: Verbundwerkstoffe und Werkstoffverbunde, Chemnitz (2011), 40-45

T. Hammers; K.A. Weidenmann; V. Schulze:
Ermüdung an rührreibgeschweißten, federstahldrahtverstärkten EN AW-6060-Matrixverbunden
Proceedings of the 18 DGM Verbundwerkstoffe Symposium: Verbundwerkstoffe und Werkstoffverbunde, Chemnitz (2011), 381-386

S. Dietrich, K. A. Weidenmann, J. Kuppinger, P. Elsner:
Prüfung und Modellierung von Sandwichstrukturen aus dem Deckschicht-Sprühprozess
Proceedings of the 18 DGM Verbundwerkstoffe Symposium: Verbundwerkstoffe und Werkstoffverbunde, Chemnitz (2011), 492-496

S. Roy, O. Stoll, K.A.Weidenmann, A. Nagel, A. Wanner:
Elastic properties of an interpenetrating metal matrix composite
Proceedings of the 18 DGM Verbundwerkstoffe Symposium: Verbundwerkstoffe und Werkstoffverbunde, Chemnitz (2011), 139-144

B. Haspel, R. Chaudhari, K.A.Weidenmann, F. Henning, P. Elsner:
Charakterisierung des Compression RTM Prozesses zur Produktion von endlosfaserverstärkten Verbundwerkstoffen
Proceedings of the 18 DGM Verbundwerkstoffe Symposium: Verbundwerkstoffe und Werkstoffverbunde, Chemnitz (2011), 227-232

M. Merzkirch, K. A. Weidenmann, V. Schulze:
Investigations on the Cyclic Crack Growth Behaviour of Spring Steel Wire Reinforced EN AW-6082
Proceedings, TMS 2011, February 27 – March 3, San Diego, California (2011), 135 -142

J. Kuppinger, F. Wafzig, F. Henning, K. Weidenmann, B. Haspel, P. Elsner:
Influence of different process conditions, different fibre contents and different fibre lengths on the fibre orientation in the polyurethane fibre spraying process
Journal of Plastics Technology (2011), 6, 44-65

S. Roy, J. Gibmeier, V. Kostov, K.A. Weidenmann, A. Nagel, A. Wanner:
Internal load transfer in a metal matrix composite having a three dimensional interpenetrating structure
Acta Materialia (2011), 59 [4], 1424-1435

C. Wörner, K.-H. Lang:
Reibermüdung ingenieurkeramischer Werkstoffe unter Variation der Beanspruchungsparameter
Abschlusskolloquium des SFB 483 am 25. Oktober 2011 in Karlsruhe, Tagungsband, 17-28

J. Altenkirch, M.J. Peel, A. Steuwer, P.J.Withers:
Comparison of methods to determine variations in unstrained unit cell parameter across welds
The Journal of Strain Analysis for Engineering Design (2011), 46 [7], 651-662

J. Altenkirch, J. Gibmeier, V. Kostov, A. Kromm, Th. Kannengiesser, S. Doyle, A. Wanner:
Time- and temperature-resolved synchrotron X-ray diffraction: observation of phase transformation and strain evolution in novel low temperature transformation weld filler materials
The Journal of Strain Analysis for Engineering Design (2011), 46 [7], 563-579

Y.Sinchuk, R.Piat, S. Roy, J. Gibmeier, A. Wanner:
Inelastic behavior of the single domain of metal-ceramic composites with lamellar microstructure
PAMM • Proc. Appl. Math. Mech. 11, (2011), 285 – 286 

M. Merzkirch, K.A. Weidenmann, V. Schulze:
Werkstoffkundliche Charakterisierung verbundstranggepresster Leichtmetallmatrix-Verbundwerkstoffe
Fortschr. Ber. VDI Reihe 2 Nr. 678, VDI-Verlag Düsseldorf, (2011), 49-72

Th. Hammers, K.A. Weidenmann, V. Schulze:
Struktur-Eigenschaft-Beziehungen von Fügezonen
Fortschr. Ber. VDI Reihe 2 Nr. 678, VDI-Verlag Düsseldorf, (2011), 143-167

R.Weingärtner, A. Kienzler, J. Hoffmeister, V. Schulze:
Effects of fluid condition and material on surface damage in ultrasonic wet peening
Shot Peening, Conference Proceedings 11 (2011), 399 – 404, ISBN: 978-0-615-49723-5

V. Schulze, M. Deuchert, C. Ruhs, P. Weber, R. Weingärtner:
Fertigungstechnologien zur Erzeugung hochgenauer Mikrostrukturen und Oberflächen
Kolloquium Mikroproduktion und Abschlusskolloquium SFB 499; 11. - 12. Oktober 2011, Karlsruhe, Herausgeber: O. Kraft, A. Haug, F. Vollertsen, S. Büttgenbach; ISBN 978-3-86644-747-9

A. Reeb, A. Ohl, K. Poser, T. Kloppenborg, A. Brosius, A.E. Tekkaya, K.A. Weidenmann:
Präparations- und Ätzmethodik zur lichtmikroskopischen Analyse von Strangpressnähten und Gefügekontrastierung für die Aluminiumlegierungen EN AW-6063 und EN AW-6082
Petzow G. (Hrsg.): Prakt. Met. Sonderband 43, (2011), 31-36, Werkstoff-Informationsgesellschaft mbH, Frankfurt, ISBN: 978-3-88355-387-0

S. Roy, J.-M. Gebert, G. Stasiuk, R. Piat, K.A. Weidenmann, A. Wanner:
Complete determination of elastic moduli of interpenetrating metal/ceramic composites using ultrasonic techniques and micromechanical modelling
Materials Science and Engineering A 528, (2011), 8226–8235 

M. Merzkirch, A. Reeb, K.A. Weidenmann, A. Wanner, V. Schulze:
Acoustic Emission Response of Reinforced Lightweight Metal Matrix Composites During Tensile and Cyclic Loading
J. Acoustic Emission, 29 (2011), 317-327

A. Cuba Ramos, H. Autenrieth, T. Strauß, M. Deuchert, J. Hoffmeister, V. Schulze:
Characterization of the transition from ploughing to cutting in micro machining and evaluation of the minimum thickness of cut
Journal of Materials Processing Technology (July 2011)

V. Schulze, J. Osterried, T. Strauß:
FE analysis on the influence of sequential cuts on component conditions for different machining strategies
1st CIRP Conference on Surface Integrity (CSI), 30.01. – 01.02.2012 Bremen, Germany, 2012, Procedia Engineering, 19, (2011), 318-323

V. Schulze, H. Meier, T. Strauß, J. Gibmeier:
High speed broaching of case hardening steel SAE 5120
Proceedings of 5th CIRP International Conference on High Performance Cutting, 4 - 7. Juni 2012, Zürich, Schweiz, 2012

T. Strauß, J. Gibmeier, A. Wanner:
Local analysis of process induced residual stress distributions for complex geometries – example: internal gearing of a gearshift sleeve
Herausgeber: R. Pabst, V. Schulze: Proceedings of the Summer School 2011, Graduate School 1483, Process Chains in Production: Interaction, Modelling and Assessment of Process Zones KIT Report-Nr. KIT-SR 7611, (2012) Karlsruhe, ISSN 1869-9669, ISBN 978-3-86644-821-6, 33-36, 

M. Schwenk, J. Hoffmeister, V. Schulze:
Process simulation of dual frequency induction surface hardening
Proceedings of the Summer School 2011 Gradute School 1483, 1-5

J. Hoffmeister, V. Schulze, R. Hessert , G. Koenig:
Residual Stress Relaxation Induced by Shot Peening in Inconel718 Under Quasistatic and Cyclic Loading.
In: Champaigne J, editor. The 11th International Conference on Shot Peening. vol. 11; (2011),225–230

M. Schwenk, T. Strauss, J. Hoffmeister, V. Schulze:
Data acquisition for numerical modelling of induction surface hardening – process specific considerations
Proceedings of 26th ASM Heat Treating Society Conference, Cincinnati, 31. Oct. - 2. Nov. (2011), 26(1), 167–76

K. A. Weidenmann, A. Wanner:
Werkstoffauswahl für den Leichtbau
F. Henning, E. Moeller (Hrsg.) Handbuch Leichtbau, Hanser-Verlag, München, (2011), ISBN 978-3-446-42267-4

F. Henning, K. A. Weidenmann:
Hybride Werkstoffverbunde
F. Henning, E. Moeller (Hrsg.) Handbuch Leichtbau, Hanser-Verlag, München, (2011), ISBN 978-3-446-42267-4

F. Henning, B. Bader, K. A. Weidenmann:
Hybride Fertigungsverfahren
F. Henning, E. Moeller (Hrsg.) Handbuch Leichtbau, Hanser-Verlag, München, (2011), ISBN 978-3-446-42267-4

A. Erz, J. Hoffmeister, V. Schulze:
Eigenschaftsänderungen bei metallischen Leichtbauwerkstoffen
Handbuch Leichtbau, Carl Hanser Verlag (2011), 555-575

J. Hoffmeister, V. Schulze, R. Hessert , G. Koenig:
Effects of the Surface Treatment on the Measured Diffraction Peak Width of Inconel 718
Champaigne J, editor. The 11th International Conference on Shot Peening. vol. 11; (2011), 201–206

M. Schwenk, T. Strauss, J. Hoffmeister, V. Schulze:
Numerical modelling of induction surface hardening and its contribution to distortionreduction
Proceedings of 3rd International Conference of Distortion Engineering, Bremen, 14-16 September. (2011), 315–22

P. Nusskern, A. Ohl, J. Hoffmeister, V. Schulze:
Bestimmung des Porositätstiefenverlaufes festgewalzter pulvertmetallurgisch hergestellter Proben aus Astaloy 85 Mo
Prakt. Met. Sonderband 43 (2011), 227-233

M. Härtelt, H. Riesch-Oppermann, T. Schwind, O. Kraft:
Statistical Evaluation of Fatigue Crack Propagation from Natural Flaws in Silicon Nitride
Journal of the American Ceramic Society, Volume 94, Issue 10, (2011), 3480–3487

M. Müller, J. Rögner, W. Bauer, R. Knitter:
Influence of the Surface Constitution on the As-Sintered Strength of Si3N4 Micro Specimens
Materials Science and Engineering A, 528, (2011), 7895-7900

J. Rögner, K.-H. Lang, G. Baumeister, V. Schulze:
Microstructure and mechanical properties of micro tensile specimens made of CuAl10Ni5Fe4 produced by micro casting
Microsystem Technologies, Volume 17, Number 2, (2011), 301-311

P. von Hartrott, C. Schweizer, O. Khalil, K.-H. Lang:
Lebensdauervorhersage von Verdichterrädern
MTZ – Motortechnische Zeitschrift, Vol 4, (2011), 316-321

L. Heritier, K.-H. Lang, M. Metzger, B. Nieweg, Y. Brontfeyn, M. Zandler, C.Schweizer:
Rechenmodelle zur Lebensdauervorhersager von Motorenbauteilen unter thermomechanischer und überlagerter hochzyklischer Ermüdungsbeanspruchung
FVV-Forschungsberichte Heft 947, Forschungsvereinigung Verbrennungskraftmaschinen e.V., Frankfurt am Main, (2010)

O. Khalil, K.-H. Lang:
Influence of Microstructure on the Quasistatic and Low Cycle Fatigue Behaviour of an AA2618 Aluminium Alloy
Procedia Engineering 10, (2011), 1339-1347

E. Kerscher, K.-H. Lang, D. Löhe:
Boundaries for Increasing of Fatigue Limit of Bearing Steel SAE 52100 by Thermomechanical Treatments
Procedia Engineering 10, (2011), 1985-1990

J. Rögner, M. Müller, J. Maisenbacher, K.-H. Lang, O. Kraft, A. Wanner, V. Schulze:
Prozess-Gefüge-Eigenschaftsbeziehungen urgeformter Mikro-proben aus Siliziumnitrid
In: O. Kraft; A. Haug; F. Vollertsen; S. Büttgenbach ; [Hrsg.]: Kolloquium Mikroproduktion und Abschlusskolloquium SFB 499 ; 11. - 12. Oktober 2011, Karlsruhe (KIT Scientific Reports ; 7591), 2011, 49-56

A.Steuwer, M. Dumont, J. Altenkirch, S. Birosca, A. Deschamps:
P.B. Prangnell, and P.J. Withers, A combined approach to microstructure mapping of an Al–Li AA2199 friction stir weld, Acta Mat, Vol 59, (2011), 3002–3011

J. Altenkirch, J. Gibmeier, A. Kromm, Th. Kannengiesser, Th. Nitschke-Pageland M. Hofmann:
In-situ study on the residual strain stability of Low Temperature Transformation (LTT)-weld filler materials using Neutron Diffraction
Mat. Sci. Eng. A, Vol 528, (2011), 5566–5575

J. Altenkirch, A. Steuwer, M.J. Peel, P.J. Withers:
Comparative Determination of the Unstrained Lattice Parameter in AA7449 Friction Stir Weld
Journal for Strain Analysis, Vol 64, Issue 7, (2011), 651-662

J. Altenkirch, J. Gibmeier, Th. Buslaps and V. Honkimäki:
EDXRD for real time observation of a gas tungsten arc welding process
Materials Science Forum Vols. 706-709 (2012), 1655-1660

J. Rebelo Kornmeier, J. Gibmeier, M. Hofmann, R.C. Wimpory:
Neutron surface residual stress scanning using optimisation of a Si-bent perfect crystal monochromator for minimising spurious strains
Materials Science Forum Vol. 681 (2011), 399-404

J. Rebelo Kornmeier, J. Gibmeier, M. Hofmann:
Minimization of spurious strains by using a Si bent-perfect-crystal monochromator: neutron surface strain scanning of a shot-peened sample, Meas
Sci. Technol. 22 (2011) 6, 065705 doi: 10.1088/0957-0233/22/6/065705

T. Strauß, H. Meier , J. Gibmeier , V. Schulze, A. Wanner:
Local residual stress distribution at the tooth root surface of a broached steel component
Materials Science Forum Vols. 706-709 (2012), 1731-1736

J. Rögner, A. Ohl, J. Gibmeier, V. Schulze, E. Kerscher:
Metallographische Charakterisierung metallischer Gläser
Prakt. Met. Sonderband 43, (2011), 37-42

Veröffentlichungen 2010

T. Böhlke, K. Jöchen, O. Kraft, D. Löhe, V. Schulze:
Elastic properties of polycrystalline microcomponents
Mechanics of Materials 42 (2010), 11 – 23

R. Piat, S. Roy, A. Wanner:
Material parameter identification of interpenetrating metal-ceramic composites
Key Engineering Materials Vols. 417-418 (2010), 53 – 56

V. Kostov, J. Gibmeier, S. Doyle, A. Wanner:
Real time monitoring of the strain evolution during rapid heat treatment of steel samples by means of synchrotron X-ray diffraction
Materials Science Forum Vols. 638-642 (2010), 2423 – 2428

H. Autenrieth, M. Weber, M. Deuchert, V. Schulze:
Investigation of the surface characteristics for the micro-cutting process with finite element simulation
Materials Science Forum Vols. 638-642 (2010), 2531 – 2536

A. Wanner:
Minimum-weight materials selection for limited available space
Materials and Design 31 (2010), 2834 – 2839

M. Müller, J. Rögner, B. Okolo, W. Bauer, R. Knitter:
Processing of micro-components made of sintered reaction-bonded silicon nitride (SRBSN). Part 2: Sintering behaviour and micro-mechanical properties
Ceramics International 36 (2010), 707 – 717

B. Okolo, J. Rögner, E. Kerscher, T. Beck, V. Schulze, A. Wanner, D. Löhe:
Size Effects in Aluminium Bronze Cast Specimens
Smart Sytems Integration and Reliability - Honorary volume on the occasion of Herbert Reichl’s birthday (2010), 740 – 747

J. Rögner, B. Okolo, J. Schneider, K.-H. Lang, A. Wanner, V. Schulze:
Charakterisierung und Prüfung von Mikrobauteilen
4. Kolloquium Mikropoduktion (2009), 105 – 110

F. A. Çetinel, M. Müller, J. Rögner, W. Bauer, J. Hausselt:
Influence of dispersant on rheology of zirconia-paraffin feedstocks and mechanical properties of micro parts fabricated via LPIM
34th International Conference on Advanced Ceramics & Composites (2010), 1-13

M. Zimmermann, V. Schulze, J. Hoffmeister:
Finite element modelling of coverage effects during shot peening of IN718
Int. J. Mat. Res. (Formerly Z. Metallkd.) 101 (2010), 951 – 962

T. Schwind, S. Fünfschilling, E. Kerscher, K.-H. Lang, R. Oberacker,

M.J. Hoffmann, T. Fett:
Failure of Alumina in Torsion Tests
Advanced Engineering Materials 2010, 12, No.9, 942-947

M. Zimmermann, M. Klemenz, V. Schulze:
Literature review on shot peening simulation
International Journal of Computational Materials Science and Surface Engineering 3 (2010), 289–310

S. Dietrich, J. Kuppinger, P. Elsner, K. Weidenmann:
Small Mass Impact Testing of Sandwich Structures
Materials Testing 52 (2010) 11-12, 765-770

T. Hammers, K. Weidenmann, E. Kerscher:
Mechanical properties of compound extruded aircraft stringer profiles under cyclic loading
Adv. Eng. Mater., 12 [7] 2010, 584-586

M. Marré, C. Weddeling, T. Hammers, M. Merzkirch, J. Rautenberg, E. Tekkaya, V. Schulze, D. Biermann, A. Zabel:
Innovative joining methods for lightweight designs, Part II, In: Aluminium, International Journal for Industry, Research and Application, [3] 2010, 55-59

S. Huber, M. Ruhstorfer, T. Hammers, M. Kronthaler, M.F. Zaeh, V. Schulze:
Innovative joining methods for lightweight designs, Part I
Aluminium, International Journal for Industry, Research and Application, [1/2] 2010, 78-83

S. Roy, J. Gibmeier, V. Kostov, K.A. Weidenmann, A. Nagel, A. Wanner
Internal load transfer in a metal matrix composite with a three-dimensional interpenetrating structure
Acta Materialia 59 (2011) 1424-1435

D. Gelmedin, K.-H. Lang:
Fatigue Behaviour of IN713 under LCF-, HCF-and superimposed LCF/HCF- loading
Procedia Engineering 2 (2010) 1343-1352

J. Kuppinger, K. Weidenmann, M. Kordick, F. Wafzig, F. Henning, P. Elsner:
Influence of fibre length and concentration on the mechanical properties of long glass fibre reinforced polyurethane, Journal of Plastics Technology 5 (2010), 205-227

J.-M. Gebert, B. Reznik, R. Piat, B. Viering, K.A. Weidenmann, A. Wanner, O. Deutschmann:
Elastic constants of high-texture pyrolytic carbon measured by ultrasound phase spectroscopy, Carbon; 48 (12) (2010), 3635-3658

V. Schulze, C. Becke, K.A. Weidenmann, S. Dietrich:
Machining Strategies for Hole Making in Composites with Minimal Workpiece Damage by Directing the Process Forces Inwards, Journal of Materials Processing Technology (2010)

B. Brylka, F. Fritzen,T. Böhlke, K.A. Weidenmann.:
Study of Experimental Methods for Interface Problems Based on Virtual Testing. PAMM - Proc. Appl. Math. Mech. 10 (2010), 109 – 110

R. Piat, S. Dietrich, J.-M. Gebert, G. Stasiuk, K.A. Weidenmann, A. Wanner, T. Böhlke, B. Drach, I. Tsukrov, A. Bussiba:
Micromechanical Modeling of CFCs Using Different Pore Approximations.
Krenkel W., Lamon J.: High Temperature Ceramic Materials and Composites, AVISO Verlagsgesellschaft mbH, Berlin, Germany (2010), 590-597

K.A. Weidenmann; E. Kerscher; M. Merzkirch:
In Situ Damage Detection With Acoustic Emission Analysis During Cyclic Loading of Wire Reinforced EN AW-6082,
Advanced Engineering Materials, 12 [7] (2010), 637-640

T. Kannengießer, A. Kromm, J. Gibmeier, M. Rethmeier:
In-situ-Analyse der Phasenumwandlungskinetik während des Schweißens
MP Materials Testing 52 (2010) 4, 204 – 210

M. Schwenk, J. Hoffmeister, C. Krause, V. Schulze:
Experimental and numerical investigation of surface induction hardening within the framework of process chain simulation
Heat Processing (8) Issue 4 (2010), 1 – 5

S. Roy, B. Butz, A. Wanner
Damage evolution and domain-level anisotropy in metal/ceramic composites exhibiting lamellar microstructures.
Acta Materialia 58 (2010) 2300–2312

N. Eswara Prasad, D. Vogt, T. Bidlingmaier, A. Wanner, E. Arzt
Low cycle fatigue and creep–fatigue interaction in short fibre reinforced aluminium alloy composite.
Materials Science and Technology 26, (2010), 1363-1372

R. Piat, T. Bohlke, O. Deutschmann, S. Dietrich, B. Drach, J.-M. Gebert, T. Gross, A. Li, B. Reznik, G. Stasiuk, I. Tsukrov, A.Wanner
Numerical Studies of the Influence of the Porosity on Macroscopic Elastic Properties of Carbon/Carbon Composites.
Proc. Appl. Math. Mech. 10, (2010), 719–720

A. Kromm, T. Kannengiesser, J. Gibmeier:
In-situ observation of phase transformations during welding of low transforamtion temperature filler material
Materials Science Forum Vol. 638-642 (2010), 3769 - 3774

 

 

Veröffentlichungen 2009

T. Hammers, M. Merzkirch, K. A. Weidenmann, E. Kerscher:

Mechanisches Verhalten ausgewählter Werkstoffsysteme verbundstranggepresster Leichtbauprofile unter quasistatischer Belastung

In: Krenkel, W.: Verbundwerkstoffe, 2009, S. 155 - 161, ISBN: 978-3-527-32615-0

 

K. A. Weidenmann, T. Hammers, M. Merzkirch, E. Kerscher:

Charakterisierung des mechanischen Verhaltens verbundstranggepresster Leichtbauprofile unter schlagartiger Beanspruchung

In: Krenkel, W.: Verbundwerkstoffe, 2009, S. 168 - 173, ISBN: 978-3-527-32615-0

 

T. Ziegler, A. Neubrand, S. Roy, A. Wanner, R. Piat:

Elastic constants of metal/ceramic composites with lamellar microstructures: Finite element modelling and ultrasonic experiments

Composites Science and Technology 69 (2009) S. 620 - 626

 

B. Kasanická, B. Okolo, G. Baumeister, M. Auhorn, T. Beck, A. Wanner, J. Haußelt, D. Löhe, V. Schulze:

On the relationship between microcasting process, material states and mechanical properties in the gold alloy Stabilor® G

Materials Science and Engineering A 501 (2009) S. 70 - 80

 

J. Rögner, M. Müller, B. Okolo, E. Kerscher, A. Wanner, V. Schulze:

Microstructure and mechanical properties of micro sized silicon nitride specimen produced by hot molding

Proceedings ISNT 2009, 6th International Conference on Nitrides and Related Materials, March 15-18, 2009, Karlsruhe, S. 106 - 107

 

H. Autenrieth, M. Weber, M. Deuchert, V. Schulze:

Investigation of Scaling Behaviour of Subsurface Work Hardening and Residual Stress States After Micro-Cutting Using Finite Element Simulation

Proceedingsof the 12th CIRP Conference on Modelling of Machining Operations. Donostia-San Sebastian, Spain, May 7-8, 2009, S. 639 – 646

 

M. Grigo, K.A. Weidenmann, P.Elsner:

Untersuchungen zum Verhalten von langfaserverstärkten Thermoplasten unter mechanischer Beanspruchung In: Krenkel, W.: Verbundwerkstoffe, 2009, S.

361-367, ISBN: 978-3-527-32615-0

 

H. Autenrieth, B. Okolo, V. Schulze, A. Wanner:

Surface workhardening and residual stresses induced by micro cutting processes

Proceedings of the 8th International Conference on Residual Stresses (ICRS-8), Denver 2008, International Centre for Diffraction Data 2009, ISSN 1097-0002, S. 608 - 615

 

T. Hammers, M. Marré, J. Rautenberg, P. Barreiro, V. Schulze, D. Biermann, A. Brosius, A. E. Tekkaya:

Influence of Mandrel’s Surface and Material on the Mechanical Properties of Joints Produced by Electromagnetic Compression

steel research int. 80 (2009) No. 5, S. 366 - 375

 

S. Roy, J. Gibmeier, A. Wanner:

Residual stresses in novel metal/ceramic composites exhibiting a lamellar microstructure

Powder Diffraction Suppl. 24 (S1), June 2009, S. 59 - 64

 

S. Roy, J. Gibmeier, A. Wanner:

In situ Study of Internal Load Transfer in a Novel Metal/Ceramic Composite Exhibiting Lamellar Microstructure Using Energy Dispersive Synchrotron X-ray Diffraction

Advanced Engineering Materials 2009, 11, No. 6, S. 471 - 477

 

H. Autenrieth, N. Herzig, J. Hoffmeister, V. Schulze, L. W. Meyer:

Influence of loading state on ductile failure behaviour of AISI 1045 in a normalized state and numerical description and application

2nd International Conference on Hot Sheet Metal Forming of High-Performance Steel, Schweden, 2009, S. 87 - 95

 

A. Wanner:

Testing of materials and structures

In: H.-J. Bullinger (Ed.): Technology Guide. Principles - Applications - Trends, Springer-Verlag Berlin Heidelberg 2009, ISBN 978-3-540-88545-0, S. 52 - 55

 

H. Autenrieth, L. Delonnoy, M. Weber, T. Hochrainer, M. Deuchert, J. Kotschenreuther, V. Schulze, P. Gumbsch:

Experimentelle und numerische Untersuchung von Größeneffekten bei der Skalierung des Mikrozerspanprozesses

Größeneinflüsse bei Fertigungsprozessen, Hrsg. F. Vollertsen, BIAS Verlag, 2009, S. 415 - 467

 

A. Ohl, M. Merzkirch, M. Grigo, B. Butz, K. A. Weidenmann:

Präparation von Dünnschliffen aus langfaserverstärkten Verbundwerkstoffen mit Polymer- oder Aluminiummatrizes zur Bestimmung der Grenzflächenscherfestigkeit mittels Push-Out Test

In: Sonderbände der praktischen Metallographie 41, Herausgeb. G. Petzow, S. 99-104, 2009

 

Merzkirch, M.; Weidenmann, K.; Kerscher, E.; Löhe, D. :

Werkstoffsysteme für verstärkte Leichtbauprofile

Fortschr. Ber. VDI Reihe 2 Nr. 668, 2009, S. 45-64, ISBN 978-3-18-366802-1, VDI-Verlag Düsseldorf

 

T. Hammers, M. Merzkirch, K. A. Weidenmann,V. Schulze,

Struktur-Eigenschafts-Beziehungen von Fügestellen,

Fortschr. Ber. VDI Reihe 2 Nr. 668, 2009, S. 115-132, ISBN 978-3-18-366802-1, VDI-Verlag Düsseldorf

 

S. Huber, M. Merzkirch, M. F. Zaeh, V. Schulze,

Applications of High-Power Diode Lasers for Aluminum Welding,

Proceeedings of SPIE, 2009

 

J. Altenkirch, A. Steuwer, M.J. Peel, P.J. Withers:
The extent of relaxation of weld residual stresses on cutting out cross-weld test-pieces, Powder Diffraction Suppl. 24 (S1), June 2009, S. S31-S36

H. Autenrieth, V. Schulze, N. Herzig, L. W. Meyer:
Ductile failure model for the description of AISI 1045 behavior under different loading conditions. Mech. Time-Depend. Mater. (2009) 13, S. 215 – 231

 

E. Brandl, R. Malke, T. Beck, A. Wanner, T. Hack:
Stress corrosion cracking and selective corrosion of copper-zinc alloys for the drinking water installation. Materials and Corrosion 2009, 60, No. 4, S. 251 - 258

 

E. Brandl, R. Malke, T. Beck, A. Wanner, T. Hack:
Stress corrosion cracking and selective corrosion of copper-zinc alloys for the drinking water installation. Materials and Corrosion 2009, 60, No. 4, S. 251 - 258

 

P. Elsner, F. Henning, K. A. Weidenmann:
Composites, in: H.-J. Bullinger (Hrsg.) Technology Guide, Springer-Verlag, Heidelberg, 2009

 

D. Gelmedin, K.-H. Lang:
Ermüdungsverhalten von Hochtemperaturwerkstoffen bei hohen Grundlasten. Forschungsberichte Heft R548, Informationstagung Tur-binen, Forschungsvereinigung Verbrennungskraftmaschinen e.V., Frankfurt am Main (2009) S. 37 - 49

 

J. Gibmeier, M. Götting and B. Scholtes:
In-situ study of the cyclic deformation behaviour of the magnesium base wrought alloy AZ31 by means of high energy synchrotron diffraction, Advances in X-ray Analysis Vol. 52, S. 397-404

 

J. Gibmeier, J. Kornmeier and M. Hofmann:
Neutron diffraction stress analysis of near surface stress gradients of surface treated steel samples, Advances in X-ray Analysis Vo. 52, S. 279-286

T. Hammers, M. Merzkirch, K.A. Weidenmann, E. Kerscher:
Mechanisches Verhalten ausgewählter Werkstoffsysteme verbund-stranggepresster Leichtbauprofile unter quasistatischer Belastung, Proceeedings of "Verbundwerkstoffe und Werkstoffverbunde 2009", 17., 2009, 155-161

 

T. Hammers, D. Pietzka, T. Kloppenborg, K. A. Weidenmann, E. Ker-scher, M. Schikorra, A. E. Tekkaya, D. Löhe:
T1 - Verbesserung der Werkstoff- und Bauteileigenschaften von Luft-fahrtstringern durch Verbundstrangpressen. In: Fortschr. Ber. VDI Rei-he 2 Nr. 668, VDI-Verlag Düsseldorf, 2009, S. 351-369, ISBN 978-3-18-366802-1

 

C. Held, J. Dadrich, R. Denninger, R. Schleich, K. A. Weidenmann, M. Liewald:
Semi-empirische Berechnungsmethode zur Berechnung des Grenz-formänderungsdiagramms auf Basis mechanischer Kennwerte
Mat.-wiss. u. Werkstofftechnik, 2009, 40, No. 11, S. 831 - 835

Th. Kannengiesser, A. Kromm, M. Rethmeier, J. Gibmeier, Ch. Genzel:
Residual stresses and in situ measurement of phase transformation in low transformation temperature, (LTT) WELDING MATERIALS, Advances in X-ray Analysis Vo. 52, S. 755-762

 

O. Khalil, C. Schweizer, P. von Hartrott, K.-H. Lang, H. Riedel:
Verbesserte Methoden zur Lebensdauerberechnung von Abgasturbolader-Radialverdichterräder aus hochwarmfesten Aluminiumlegierungen. FVV-Forschungsberichte Heft R544, Informationstagung Turbinen, Forschungsvereinigung Verbrennungskraftmaschinen e.V., Frankfurt am Main (2008), S. 35 – 52

 

O. Khalil, C. Schweizer, K.-H. Lang, T. Seifert, H. Riedel:
Verbesserte Methoden zur Lebensdauerberechnung von Abgasturbolader-Radialverdichterräder aus hochwarmfesten Aluminiumlegierungen. FVV-Forschungsberichte Heft 548, Informaitonstagung Turbinen, Forschungsvereinigung Verbrennungskraftmaschinen e.V., Frankfurt am Main (2009), S. 159 - 182

 

A. Kienzler, J. Hoffmeister, V. Schulze:
Surface finishing of micro moulds inserts made of precipitation-hardened steel. Proceedings 4m/ICOMM Conference 23.-25.9.2009, Karlsruhe, S. 237 – 240

 

A. Kienzler, M. Deuchert, V. Schulze:
Burr Minimization and Removal by Micro Milling Strategies or Micro Peening Processes, Burrs – Analysis, Control and Removal: Proceedings of the CIRP International Conference on Burrs (Hrsg.: J. C. Aurich, D. Dornfeld), Universität Kaiserslautern, 02.-03.04.2009

 

A. Kienzler, B. Okolo, V. Schulze, A. Wanner:
Spatially resolved strain measurements on micro moulds. Proceedings of the 8th Int. Conference on Residual Stresses (ICRS-8) Denver 2008, International Centre for Diffraction Data 2009, ISSN 1097-0002, S. 437 – 443

 

A. M. Klaska, T. Beck, A. Wanner, D. Löhe:
Residual stress and damage development in the aluminium alloy EN AW-6061 particle reinforced with Al2O3 under thermal fatigue laoding
Materials Science and Engineering A 501 (2009) S. 6 - 15
 
M. Klemenz, V. Schulze:
Numerische Untersuchungen zur Auswirkung von Prozess- und Geo-metrieparametern beim Kugelstrahlen von 42CrMo4. HTM Heat. Treatm. Mat. 64 (2009) 3, S. 150 - 158

R. Lin Peng, J. Gibmeier, G.C. Chai, S. Johansson:
Load partitioning in a duplex stainless steel with surface strength gradient and residual stresses, Advances in X-ray Analysis Vo. 52, S. 773-780

 

C. Mende, E. Heits, A. Schulz, H.-J. Bauer, A. Wanner:
Acoustic Emission Testing of Highly Loaded Combustor Liner Tiles for Gas Turbines. OMMI, 2009, Volume 6, Issue 1 (http://www.ommi.co.uk/)

 

J. Rögner, B. Okolo, J. Schneider, K.-H. Lang, A. Wanner, V. Schulze:
Charakterisierung und Prüfung von Mikrobauteilen. In: F. Vollertsen, S. Büttgenbach, O. Kraft, W. Michaeli (Hrsg.): 4. Kolloquium Mikroproduk-tion. Bias Verlag, Bremen ISBN: 978-3-933762-32-0 (2009), S. 105 - 110
 

S. Roy, J. Gibmeier and A. Wanner:
Residual stresses in novel metal/ceramic composites exhibiting
a lamellar microstructure, Powder Diffraction Suppl. 24 (S1), June 2009, S. S59-64

 

S. Roy, J.-M. Gebert, A. Wanner:
Complete stiffness characterization of a lamellar metal/ceramic composite using ultrasonic spectroscopy techniques. Proceedings of the 17th Int. Conference on Composite Materials, July 27-31, 2009, Edinburgh, Scotland, Paper No. IF19.1

T. Schalk, K.-H. Lang, D. Löhe:
Fretting Fatigue of Engineering Ceramics. Ceramic Engineering and Science Proceedings 29, 3 (2009), S. 101 - 110

J. Schneider, K.-H. Zum Gahr, A. Kienzler, V. Schulze:
Influence of surface condition on wear and demoulding behaviour of mould inserts for micro powder injection moulding. In: A. Fischer, K. Bobzin (ed.) International Symposium on Friction, Wear and Wear Pro-tection 2008, Aachen (2009), S. 629 - 636Lehrstuhl für Werkstoffkun-de, Technische Universität Kaiserslautern

 

V. Schulze, M. Deuchert, A. Kienzler, Ch. Ruhs, P. Weber:
Prozessübergreifende Betrachtung abtragender Verfahren zur Mikro-formeinsatzherstellung, 4. Kolloquium Mikroproduktion, 28.-29.10.2009, Bremen, S. 125 – 132

 

V. Schulze, J. Schneider, L. Mattson:
Quality Assurance and metrology: Test methods, equipment, comparability and reproducability. In: P. Johander, H.-J. Ritzhaupt-Kleissl (eds.): Ceramics Processing in Micro Technology, S. 305 - 320

 

T. Schwind, E. Kerscher, K.-H. Lang:
Fatigue of Alumina Under Cyclic Torsion Loading. Advanced Engineering Materials 11 [7] (2009), S. 586 – 589

 

B. Thielicke, M. Grigo, J. Dreißig:
LFT-Kennwerte aus Zugversuchen in Konstruktion, Teil Ingenieurwerkstoffe 10/2009

 

K. A. Weidenmann, T. Hammers, M. Merzkirch, E. Kerscher:
Charakterisierung des mechanischen Verhaltens verbundstranggepresster Leichtbauprofile unter schlagartiger Beanspruchung, Proceeedings of "Verbundwerkstoffe und Werkstoff-verbunde 2009", 17, 2009, 168-173,

K.A. Weidenmann, R. Tavangar, L. Weber:
Mechanical Behaviour of Diamond Reinforced Metals, Materials Science & Engineering A, 523, 226-234, 2009

 

K. A. Weidenmann, R. Tavangar, L. Weber:
Rigidity of Diamond Reinforced Metals featuring high Particle Contents, Composite Science and Technology, 69 [10] 1660-1666, 2009

Veröffentlichungen 2008

G. Baumeister, B. Okolo, J. Rögner:
Microcasting of Al bronze: influence of casting parameters on the microstructure and the mechanical properties
Microsystem Technology

J. Rögner, E. Kerscher, V. Schulze, D. Löhe:
Mechanical Properties of Primary Shaped Notched Micro Specimens Made of Aluminium Bronze
Advanced Engineering Materials 2008, 10, No. 6, S. 529 – 533

P. Barreiro, V. Schulze, D. Löhe:
Influence of Process Parameters on Structure and Mechanical Properties of Joints produced by Electromagnetic Forming and Friction Stir Welding
Advanced Materials Research Vol. 43 (2008) S. 47 – 56

M. Merzkirch, K. A. Weidenmann, E. Kerscher, D. Löhe:
Documentation of the Corrosion of Composite-Extruded Aluminium Matrix Extrusions using the Push-Out Test
Advanced Materials Research Vol. 43 (2008) S. 17 – 22

T. Hammers, E. Kerscher, D. Löhe, M. Schikorra:
Mechanical Properties of Compound Extruded Stringer Profiles
Ins. 1st Eucomas, Berlin, 26./27.05.2008, VDI-Berichte 2028, S. 445 - 446, ISBN 978-3-18-092028-3

T. Kloppenborg, T. Hammers, M. Schikorra, E. Kerscher, A. E. Tekkaya, D. Löhe:
Prototype Manufacturing of Extruded Aluminium Aircraft Stringer Profiles with Continuous Reinforcement
Advanced Materials Research Vol. 43 (2008) S. 167 – 174

T. Hammers, M. Marré, J. Rautenberg, P. Barreiro, V. Schulze, D. Löhe, A. Brosius, A. E. Tekkaya:
Influence of Mandrel’s Surface on the Mechanical Properties of Joints Produced by Electromagnetic Compression
In: 3rd Int. Conf. on High Speed Forming, 11.3.-12.3.2008, Dortmund, Germany, Proceedings. S. 245 - 256, ISBN 3-9809535-3-X

K. Weidenmann, E. Kerscher, D. Löhe:
Gefüge und Eigenschaften verbundextrudierter Aluminiumlegierungen
MP Materials Testing 50 (2008) 3, S. 133 – 141

E. Kerscher, K.-H. Lang, D. Löhe:
Increasing the fatigue limit of a high-strength bearing steel by thermomechanical treatment
Materials Science and Engineering A 483-484 (2008) S. 415 – 417

P. A. Gruber, J. Böhm, F. Onuseit, A. Wanner, R. Spolenak, E. Arzt:
Size effects on yield strength and strain hardening for ultra-thin Cu films with and without passivation: A study by synchrotron and bulge test techniques
Acta Materialia 56 (2008) 2318 – 2335

A. Kienzler, J. Schneider, V. Schulze, K.-H. Zum Gahr:
Oberflächennachbearbeitung von Mikroformeinsätzen für das Mikropulverspritzgießen
HTM J. Heat Treatm. Mat. 63 (2008) 4, S. 207 – 212

A. Rossoll, C. Otto, B. Moser, L. Weber, A. Wanner, A. Mortensen:
Measurement of damage evolution in continuous ceramic fibre-reinforced metals by acoustic emission
Scripta Materialia 59 (2008) S. 842 – 845

J.-M. Gebert, A. Wanner, R. Piat, M. Guichard, S. Rieck, B. Paluszynski, T. Böhlke:
Application of the Micro-Computed Tomography for Analyses of the Mechanical Behavior of Brittle Porous Materials
Mechanics of Advanced Materials and Structures, 15:467-473, 2008, ISSN: 1537-6494

V. Runser, D. Löhe, V. Schulze:
Development and evaluation of a model for solid-state phase transformations during casting of ductile cast iron
Proceedings 2nd Int. Conference on Distortion Engineering 2008, Bremen, 17.-19.9.2008, S. 125 – 132

M. Merzkirch, K. A. Weidenmann, E. Kerscher, D. Löhe:
The use of acoustic emission to determine damage evolution during cyclic loading of wire reinforced AlSiMg0.5 Matrix
P. D. Portella, T. Beck, M. Okazaki,
Proceedings of 6th Int. Conference on Low Cycle Fatigue - LCF6, Berlin, 8.-12.9.2008, S. 649 – 654

M. Merzkirch, K. A. Weidenmann, E. Kerscher, D. Löhe:
Mechanical Properties of Hybrid Composite Extrusions of an Aluminium-Alumina Wire Reinforced Aluminium Alloy
Materials Science and Technology 2008, October 5-9, 2008, Pittsburgh,Pennsylvania, S. 2552 – 2562
Processing, Properties, and Performances of Composite Materials

T. Schwind, T. Schalk, E. Kerscher, T. Beck, K.-H. Lang, D. Löhe:
Thermal, mechanical and fretting fatigue of silicon nitride
International Journal of Materials Research 99 (2008) 10, S. 1090 – 1096

T. Erbacher, A. Wanner:
X-ray analysis of steep residual stress gradients: The 2θ-derivative method
International Journal of Materials Research 99 (2008) 10, S. 1071 - 1078

E. Kerscher, A. Reif, D. Löhe:
Schadensanalyse an einem modernen Cross-Country-Fahrrad
Praktische Metallographie Sonderband 40 (2008), Hrsg.: G. Petzow, DGM, S. 165 – 170

M. Deuchert, M. Weber, H. Autenrieth, J. Fleischer, V. Schulze, D. Löhe:
Influence of process parameters on the specific reaction of forces and surface characteristics in orthogonal micro-cutting
3rd CIRP International Conference High Performance Cutting, 12-13th June, 2008, S. 675 – 685

T. A. Egly, K.-H. Lang, D. Löhe:
Influence of Phase Shift and Strain Path on the Thermomechanical Fatigue Behaviour of CMSX-4 Specimens
International Journal of Fatigue 30 (2008), S. 249 – 256

T. Hammers, A. Uihlein, K.-H. Lang, D. Löhe:
Development of Damage in Cast Iron During Superimposed Low Frequency Thermal-Mechanical and Higher Frequency Mechanical Loading
K. J. Hsia, M. Göken, P. D. Portella, N. R. Moddy (Eds.): Plasticity, Failure and Fatigue in Structural Materials - from Macro to Nano: Proceedings of the Hael Mughrabi Honoray Symposium. TMS, Warrendale, PA, USA, ISBN 978-0-87339-714-8 (2008), S. 253 – 258

A. Kienzler, B. Okolo, A. Wanner, V. Schulze, D. Löhe:
A Reliable Tool for the Improvement of Micro Powder Injection Moulds Made of Steel
Advanced Engineering Materials 10 (2008), S. 661 – 665

J. Rögner, B. Okolo, S. Kurzenhäuser, M. Müller, W. Bauer, H.-J. Ritzhaupts-Kleissl, E. Kerscher, V. Schulze:
Relationships between Process, Microstructure and Properties of Molded Zirconia Micro Specimens
Microsystems Technologies 14 (2008), S. 1831 – 1837

S. Roy, A. Wanner:
Metal/ceramic composites from freeze-cast ceramic preforms: Domain structure and elastic properties
Composites Science and Technology, 68, 2008, S. 1136 – 1143

S. Roy, B. Butz, A. Wanner:
Damage evolution and anisotropy in freeze cast metal/composites: An in-situ SEM analysis
13th European Conference on Composite Materials (ECCM13), Stockholm, Schweden, 2.-5. Juni 2008, paper no. 0303

H. Autenrieth, M. Weber, D. Deuchert, D. Löhe, V. Schulze, P. Gumbsch, J. Fleischer:
Influence of process parameters on the specific active and passive forces, subsurface hardening and residual stresses in micro-cutting
Proceedings 2nd Int. Conference on Distortion Engineering 2008, Bremen, 17.-19.9.2008, S. 153 – 160

T. Hammers, E. Kerscher, K. Weidenmann, D. Löhe:
Composites I: Mechanical Properties of Compound Extruded Unidirectional Reinforced Aluminium Alloys under Quasi-static Loading
Aluminium Alloys, Volume 2, Their Physical and Mechanical Properties, Edited by J. Hirsch, B. Skrotzki, G. Gottstein, DGM, WILEY-VCH, 2008, S. 2245 – 2250

E. Kerscher, K.-H. Lang, D. Löhe:
Rissausbreitungsverhalten in hochfesten Stählen
Praktische Metallographie Sonderband 40 (2008), Hrsg.: G. Petzow, DGM, S. 305 – 310

G. Baumeister, B. Okolo, J. Rögner, R. Ruprecht, E. Kerscher, V. Schulze, J. Haußelt, D. Löhe:
New Results on Microcasting of Al Bronze
Microsystem Technologies 14 (2008), S. 1813 – 1821

T. Hammers, A. Uihlein, K.-H. Lang, D. Löhe:
Development of Damage in Cast Iron During Superimposed Low Frequency Thermal-Mechanical and Higher Frequency Mechanical Loading
K. J. Hsia, M. Göken, P. D. Portella, N. R. Moddy (Eds.): Plasticity, Failure and Fatigue in Structural Materials - from Macro to Nano: Proceedings of the Hael Mughrabi Honoray Symposium. TMS, Warrendale, PA, USA, ISBN 978-0-87339-714-8 (2008), S. 253 – 258

Ch. Munzinger, J. Rögner, A.-M. Dieckmann:
Sinterfügen von Micro-PIM-Bauteilen - Ein Montagekonzept in der Mikrotechnik
wt Werkstattstechnik online 98, Heft 9 (2008), S. 701 – 705

T. Schalk, K.-H. Lang, D. Löhe:
Fretting Fatigue of Engineering Ceramics
K. J. Hsia, M. Göken, P. D. Portella, N. R. Moddy (Eds.): Plasticity, Failure and Fatigue in Structural Materials - from Macro to Nano: Proceedings of the Hael Mughrabi Honoray Symposium. TMS, Warrendale, PA, USA, ISBN 978-0-87339-714-8 (2008), S. 189 – 194

A. Uihlein, K.-H. Lang, D. Löhe:
Low Cycle Fatigue Behaviour of Cast Irons at Different Temperatures
P. D. Portella, T. Beck, M. Okazaki, Proceedings of 6th International Conference on Low Cycle Fatigue - LCF6, Berlin, 8.-12.9.2008, S. 371 – 376

O. Ulrich, K.-H. Lang, D. Löhe:
Fatigue of Al2O3-AlSi12 and TiC-AlSi12 Preform-MMCs at Room and Elevated Temperatures
P. D. Portella, T. Beck, M. Okazaki, Proceedings of the 6th International Conference on Low Cycle Fatigue - LCF6, Berlin, 8.-12.9.2008, S. 217 – 222

P. Hähner, C. Rinaldi, V. Bicego, E. Affeldt, T. Brendel, H. Andersson, T. Beck, H. Klingelhöffer, H.-J. Kühn, A. Köster, M. Loveday, M. Marchionni, C. Rae:
Research and development into a European code-of-practice for strain-controlled thermo-mechanical fatigue testing
International Journal of Fatigue 30 (2008) S. 372 – 381

J. Hoffmeister, V. Schulze, A. Wanner, R. Hessert, G. König:
Thermal Relaxation of Residual Stresses induced by Shot Peening in IN718
Proceedings of the 10th International Conference on Shot Peening, 2008, S. 157 – 162

H. Autenrieth, M. Weber, V. Schulze, P. Gumbsch:
Investigation of Process-Specific Size Effects by 3D-FE-Simulations
High Performance Computing in Science and Engineering: Transactions of High Performance Computing Center, Stuttgart (HLRS), S. 543 - 558
Low Cycle Fatigue Behaviour of Cast Irons at Different Temperatures
P. D. Portella, T. Beck, M. Okazaki,Proceedings of 6th International Conference on Low Cycle Fatigue - LCF6, Berlin, 8.-12.9.2008, S. 371 – 376

A. Uihlein, K.-H. Lang, D. Löhe:
Lifetime Behaviour at Superimposed Thermal-Mechanical and Mechanical Loading
Proceedings of the XI International Congress and Exhibition on Experimental and Applied Mechanics (SEM 2008), June 2-5, 2008. Society for Experimental Mechanics, Inc., Bethel, Connecticut, USA, ISBN 0-912053-99-2 (CD-ROM) 2008

K. A. Weidenmann, A. M. Klaska, E. Kerscher, D. Löhe:
Gefüge hybrider Verbundstrangpressprofile auf Aluminiumbasis/Microstructure of Hybrid Composite Extrusions with Aluminium-Based Matrices
Praktische Metallographie, 45 (2008) 11, S. 533 – 545

T. Beck, K. Rau:
Temperature measurement and control methods in TMF testing - a comparison and evaluation
International Journal of Fatigue 30 (2008) S. 226 – 233

V. Schulze, M. Klemenz, M. Zimmermann:

State of the Art in Shot Peening Simulation
Proceedings of the 10th International Conference on Shot Peening, 2008, S. 53 – 62

M. Zimmermann, V. Schulze, H. U. Baron, D. Löhe:

A Novel 3D Finite Element Simulation Model for the Prediction of the Residual Stress State after Shot Peening
Proceedings of the 10th International Conference on Shot Peening, 2008, S. 63 – 68

M. Zimmermann, M. Klemenz, V. Schulze, D. Löhe:
Numerical Studies on the Influence of Thickness on the Residual Stress Development During Shot Peening
High Performance Computing in Science and Engineering: Transactions of High Performance Computing Center, Stuttgart (HLRS), S. 481 – 492

M. Weber, H. Autenrieth, J. Kotschenreuther, P. Gumbsch, V. Schulze, D. Löhe, J. Fleischer:
Influence of Friction and Process Parameters on the Specific Cutting Force and Surface Characteristics in Micro Cutting
Machining Science and Technology, 12 (2008), S. 474 – 497

 

Veröffentlichungen 2007

M. Klemenz, M. Zimmermann, V. Schulze, D. Löhe:

Numerical Prediction of the Residual Stress State after Shot Peening

In: W. E. Nagel, W. Jäger, M. Resch (ed.): High Performance Computing in Science and Engineering`06, Springer-Verlag 2007, ISBN-13 978-3-540-36165-7, S. 437-448

 

T. Miokovic, V. Schulze, O. Vöhringer, D. Löhe:

Influence of cyclic temperature changes on the microstructure of AISI 4140 after laser surface hardening

Acta Materialia 55 (2007) S. 589-599

 

K. A. Weidenmann, C. Fleck, V. Schulze, D. Löhe:

Mechanical properties of rope-reinforced aluminium extrusions under quasistatic loading conditions

International Journal of Materails Research 98 (2007) 1, S. 39-46

 

A. M. Klaska, A. Ohl, E. Kerscher, T. Beck, D. Löhe:

Gefügedarstellung der stranggepressten Aluminiumknetlegierung EN AW-6061 und der MMC-Werkstoffe EN AW-6061 verstärkt mit 15 und 22 Vol.-% Al2O3-Partikeln

Praktische Metallographie 44 (2007) 1, S. 33-51

 

B. Okolo, F. Pérez-Willard, J. Hawecker, D. Gerthsen, A. Wanner:

Focused Ion Beam Study of the Effects of Shot Peening on the Subsurface Microstructure of Normalized Pearlitic Steel

Journal of Materials Processing Technology 183 (2007) S. 160-164

 

H. Autenrieth, M. Weber, J. Kotschenreuther, V. Schulze, D. Löhe, P. Gumbsch, J. Fleischer:

Influence of friction and process parameters on the specific cutting force and surface characteristics in micro cutting

Proceedings of the 10th CIRP International Workshop on Modeling of Machining Operations, 27-28.08.2007, Ed. F. Micari, L. Filice, ISBN: 978-88-95267-04-3, S. 539-546

 

A. Kienzler, Ch. Horsch, V. Schulze, D. Löhe:

Application of micro peening for deburring and surface conditioning of micro milled moulds

Proceedings of the /th euspen International Conference, Bremen, May 2007,

S. 372-375

 

K. A. Weidenmann, A. Klaska, E. Kerscher, D. Löhe:

Gefüge hybrider Verbudstrangpressprofile auf Aluminiumbasis

Praktische Metallographie, Sonderband 39 (2007), S. 231-152

 

E. Kerscher, K.-H. Lang, D. Löhe:

Bewertung der Schwingfestigkeitssteigerung bei bainitischem 100Cr6 unter Berücksichtigung der Einschlussgrößen

Praktische Metallographie, Sonderband 39 (2007), S. 147-152

 

P. Barreiro, V. Schulze, D. Löhe:

Investigation of the Influence of Process Parameters on the Mechanical Behaviour under Cyclic Load at AA6060 Joints produced by Laser Bifocal Hybrid Welding

Proceedings of the Fourth International WLT-Conference on Lasers in Manufacturing 2007, Munich, June 2007, S. 37-42

 

K. A. Weidenmann, Th. Schwind, E. Kerscher, D. Löhe:

Zyklische Beanspruchung drahtverstärkter Verbundstrangpressprofile mit Aluminiummatrix

Materialwissenschaften und Werkstofftechnik 2007, 38, No. 2, S. 75-78

 

N. Trapp, M. Fiderer, V. Schulze, D. Löhe:

Strategies for the case hardening simulation of components with complex geometries

Proceedings, 5th Internatioinal Conference Quenching and Control of Distortion, 25-27 April 2007, Berlin, Ed.: J. Grosch, J. Kleff, Th. Lübben

 

M. Marré, P. Barreiro, M. Schomäcker, A. Brosius, V. Schulze, A. E. Tekkaya, D. Löhe:

Characteristics of Composite Extruded Tubes for Joining by Electromagnetic Compression

Proceedings of the 2nd ICNFT, Bremen, September 2007, ISBN: 978-3-933762-22-1, S. 461-470

 

J. Kotschenreuther, H. Autenrieth, M. Weber, J. Fleischer, V. Schulze, D. Löhe, P. Gumbsch:

Influence of Multiple Machining Steps on the Specific Cutting Force and Surface Characteristics in Micro Cutting

Proceedings of the 2nd ICNFT, Bremen, September 2007, ISBN: 978-3-933762-22-1. S. 551-561

 

J. Fleischer, D. Löhe, J. Kotschenreuther, V. Schulze, M. Deuchert, G. Halvadjiysky, S. Haupt, A. Kienzler:

Fertigungsverfahren in der Mikrotechnik

wt Werkstattstechnik online Jahrgang 97 (2007) H. 11/12, S. 847-851

 

J. Schulte-Fischedick, S. Seiz, N. Lützenburger, A. Wanner, H. Voggenreiter:

The crack development on the micro- and mesoscopic scale during the pyrolysis of carbon fibre reinforced plastics to carbon/carbon composites

Composites: Part A 38 (2007) S. 2171-2181

 

M. Weber, T. Hochrainer, P. Gumbsch, H. Autenrieth, L. Delonnoy, V. Schulze, D. Löhe, J. Kotschenreuther, J. Fleischer:

Investigation of size-effects in machining with geometrically defined cutting edges.

Machining Science and Technology (2007) 11, S. 447-473

 

G. Garces, G. Bruno, A. Wanner:

Load transfer in short fibre reinforced metal matrix composites

Acta Materialia Vol. 55 No. 16 (2007) S. 5389-5400

 

B. Okolo, J. Rögner, E. Kerscher, T. Beck, V. Schulze, A. Wanner, D. Löhe:

Size effects in Aluminium bronze cast specimens

in: Proceedings of the 1st Int. Congress on Microreliability and Nanoreliability in Key Technology Applications (MicroNanoReliability), Sept. 2-5, 2007, Berlin

 

J. Schneider, A. Kienzler, M. Deuchert, V. Schulze, J. Kotschenreuther, K.-H. Zum Gahr, D. Löhe, J. Fleischer:

Formeinsätze aus Stahl für das Mikro-Pulverspritzgießen: mechanische Strukturierung, Oberflächenbehandlung und tribologische Charakterisierung

In: O. Kraft, B. Emmerich (Hrsg.): Kolloquium Mikroproduktion - Fortschritte, Verfahren, Anwendungen, Forschungszentrum Karlsruhe (2007) ISBN 978-3-923704-61-3, S. 143-149

 

J. Rögner, B. Okolo, M. Müller, E. Kerscher, V. Schulze, T. Beck, D. Löhe:

Relationships between Process, Microstructure and Property of Molded Zirconia Micro Specimens

Proceedings MicroNanoReliability 2007, Berlin, 2.-5. Sept. 2007, Micromaterials and Nanomaterials, ISSN 1619-2486, Vol. 6, S. 202-203

 

M. Müller, J. Rögner, B. Okolo:

Factors Influencing the Mechanical Properties of Moulded Zirconia Micro Parts

In: Proceedings of the European Ceramic Society, Berlin, June 17-21, 2007

 

J. Rögner, B. Okolo, S. Kurzenhäuser, M. Müller, W. Bauer, H.-J. Ritzhaupt-Kleissl, E. Kerscher, T. Beck, V. Schulze, D.Löhe:

Prozess-Gefüge-Eigenschaftsbeziehungen für urgeformte keramische Mikrobauteile

Kolloquium Mikroproduktion, 22.-23.11.2007, Karlsruhe, Forschungszentrum Karlsruhe, ISBN 978-3-923704-61-3, S. 135-141

 

G. Baumeister. B. Okolo, J. Rögner, J. Haußelt, T. Beck, D. Löhe, R. Ruprecht, V. Schulze:

Prozess-Gefüge-Eigenschaftsbeziehungen beim Mikroguss von Al-Bronze

In: Kolloquium Mikroproduktion, 22.-23.11.2007, Karlsruhe, Forschungszentrum Karlsruhe, ISBN 978-3-923704-61-3, S. 115-120

 

S. Thalmair, A. Fischersworring-Bunk, F.-J. Klinkenberg, K.-H. Lang, D. Löhe:

Zur thermomechanischen Bewertung hochbelasteter Aluminium-Zylinderköpfe

MP Materials Testing, Vol. 49, Nr. 3 (2007) S. 113-117

 

S. Seyedi, K.-H. Lang, D. Löhe:

Fatigue Behaviour of Case Hardened P/M Steels

Key Engineering Materials, Vols. 345-346 (2007) S. 371-374

 

T. Schalk, T. Schwind, K.-H. Lang, E. Kerscher, D. Löhe:

Thermische, mechanische und Reibermüdung ingenieurkeramischer Werkstoffe

Sonderforschungsbereich 483, Tagungsband zum 3. Statuskolloquium am 18. Oktober 2007, ISBN 978-3-933733-00-9 (2007) S. 113-128

 

D. Löhe, K.-H. Lang, T. Beck:

Wechselwirkungen thermisch und mechanisch induzierter Ermüdungsbeanspruchungen

DVM-Bericht Nr. 239, Deutscher Verband für Materialprüfung und -forschung e.V. Berlin, ISSN 1616-4687 (2007) S. 329-349

 

M. Härtelt, H. Riesch-Oppermann, T. Schwind, O. Kraft:

Lifetime Prediction for Ceramic Components under Cyclic Tensile and Torsional Loading

Proc. 10th EcerS Conf., Göller Verlag, Baden-Baden (2007) ISBN 3-87264-022-4, S. 254-260

 

T. Schwind, E. Kerscher, K.-H. Lang, D. Löhe:

Influence of biaxial cyclic loadings on the fatigue behaviour of high-performance-ceramics containing glassy phases

Proc. 10th EcerS Conf., Göller Verlag, Baden-Baden (2007) ISBN 3-87264-022-4, S. 248-253

Veröffentlichungen 2005

Erbacher, Thomas; Beck, Tilmann; Vöhringer, Otmar:

Interaction between residual stresses and surface defects in alumina ceramics under tribological loading

Materialwissenschaften und Werkstofftechnik 2005, 36, No. 3/4, S. 148 - 156

 

Nejma, Rachid; Lang, Karl-Heinz; Löhe, Detlef:

Isothermal and Thermal-Mechanical Fatigue of Alumina

Materialwissenschaften und werkstofftechnik 2005, 36, No. 3/4, S. 136 - 139

 

Löhe, Detlef; Beck, Tilmann:

Mikro-Urformen - der SFB 499

In: Kolloquium Mikroproduktion, Fortschritte, Verfahren; Anwendungen (Hrsg.: U. Dilthey, Th. Dorfmüller), RWTH Aachen, ISBN 2-86130-999-8, S. 23 - 31

 

Auhorn, Markus; Kasanická, Barbora; Beck, Tilmann; Schulze, Volker; Löhe, Detlef:

Charakterisierung und mechanische Prüfung von Mikroproben aus Au58Ag23Cu12Pd5 und ZrO2

In: Kolloquium Mikroproduktion, Fortschritte, Verfahren, Anwendungen (Hrsg.: U. Dilthey, Th. Dorfmüller), RWTH Aachen, ISBN 3-86130.999-8, S. 215 - 224

 

Horsch, Christoph; Schulze, Volker; Löhe, Detlef:

Feistbearbeitung gefräster Mikrostrukturen aus Werkzeugstahl

In: Kolloquium Mikroproduktion, Fortschritte, Verfahren, Anwendung (Hrsg.: U. Dilthey, Th. Dorfmüller), RWTH Aachen, ISBN 3-86130-999-8, S. 197 - 204

 

Ottlik, Aysegül; Schulze, Volker; Pintschovius, L.; Müller, Hermann; Löhe, Detlef:

Analysis of residual stresses and distortions in brazed joints of cemented carbide and steel

Materials Science Forum Vols. 490 - 491 (2005), S. 491 - 496

 

Kasanická, Barbora; Wroblewski, Th.; Schulze, Volker; Löhe, Detlef:

Analysis of residual stresses in micro Powder injection moulded micro bending specimens made of zirconia

Materials Science Forum Vols. 490 - 491 (2005), S. 503 - 508

 

Biesinger, Frank; Söhner, J.; Delonnoy, Lionel; Schmidt, C.; Schulze, Volker; Schmidt, J.; Vöhringer, Otmar; Weule; Hartmut:

Simulation des Spanbildungsprozesses beim Hochgeschwindigkeitsfräsen

In: Hochgeschwindigkeitsspanen, Hrsg.: H. K. Tönshoff, F. Hollmann, WILEY-VCH Verlag, ISBN 3-527-31256-0, S. 207 - 228

 

Hochrainer, Thomas; Delonnoy, Lionel; Kotschenreuther, Jan; Schulze, Volker; Löhe, Detlrf; Gumbsch, Peter; Fleischer, Jürgen:

An integrated approach to the modeling of size-effects in machining with geometrically defined cutting edges

In: 8th CIRP International Workshop on Modeling of Machining Operations, Hrsg.: R. Neugebauer, Frauenhofer-Institute for Machine Tools and Forming Technology IWU, 2005, ISBN 3-937524-X, S. 123 - 129

 

Franz, Clemens; Besserdich, Gerhard; Schulze, Volker; Müller, Hermann; Löhe, Detlef:

Influence of transformation plasticity on residual stresses and distortions due to the heat treatment of steels with diffrent carbon content

Materials Science Forum Vols. 490 - 491 (2005), S. 47 - 52

 

Ott, Michael H.; Kämpfe, Andreas; Löhe, Detlef:

Application of a high temperature chamber for X-ray stress analysis

MP Materials Testing - Materialprüfung (2005) 47. Jahrgang, Nr. 5, s. 294 - 298

 

Weidenmann, Kay A.; Fleck, Claudia; Schulze, Volker; Löhe, Detlef:

Analyse der Mikrostruktur und des Eigenspannungszustandes seilverstärkter Aluminiumstrangpressprofile

Materialwissenschaft und Werkstofftechnik, 2005, 36, No. 7, S. 307 - 312

 

Horsch, Christoph; Schulze, Volker; Löhe, Detlef:

Material States and Surface Conditioning for Mold Inserts

In: Advanced Micro and Nanosystems Vol. 3. Microengineering of Metals and Ceramics. (Ed.: H.Baltes, O.Brand, G.K.Fedder, C.Hierold, J.Korvink, O.Tabata) WILEY-VCH 2005, ISBN 3-527-31208-0,S. 221 - 249

 

Kasanická, Barbora; Auhorn, Markus; Schulze, Volker; Löhe, Detlef:

Analysis of Microstructure, Surface Topography and Mechanical Properties of Micracast Specimens Made of the Dental Gold Alloy Stabilor G

In: Advanced Micro and Nanosystems Vol. 4. Microengineering of Metals and Ceramics. (Ed.:H.Baltes, O.Brand, G.K.Fedder; C. Hierold, J.Korvink, O.tabata) WILEY-VCH 2005, ISBN 3-527-31493-8, S. 523 - 553

 

Auhorn, Markus; Kasanická, Barbora; Beck, Tilmann; Schulze, Volker; Löhe, Detlef:

Microstructure, Surface Topography and Mechanical Properties of Molded ZrO² Microspecimens

In: Advanced Micro and Nanosystems Vol. 4. Microengineering of Metals and Ceramics. (Ed.:H.Baltes, O.Brand, G.K.Fedder; C. Hierold, J.Korvink, O.tabata) WILEY-VCH 2005, ISBN 3-527-31493-8, S. 555 - 553

 

Uihlein, Andreas; Mohrmann, R.; Lang, Karl-Heinz; Riedel, Hermann:

Entwicklung von Rechenmodellen zur Lebensdauervorhersage von Motorbauteilen unter thermisch-mechanischer Ermüdungsbeanspruchung

Informationstagung Motoren, Herbst 2005, Forschungsvereinigung Verbrennungskraftmaschinen, Heft R 531 (2005), S. 121 - 138

 

Delonnoy, Lionel; Hochrainer, Thomas; Schulze, Volker; Löhe, Detlef; Gumbsch, Peter:

Similarity considerations on the simulation of turning processes of steels

Zeitschrift für Metallkunde 96 (2005) 7, S. 761 - 769

 

Horsch, Christoph; Schulze, Volker; Löhe, Detlef:

Vermessung und Bewertung der Oberflächentopographie von Mikrobauteilen - A Measurement and Evaluation of the Surface Topography of Microcomponents

Praktische Metallographie 42 (2005) 8, S. 377- 386

 

Krug, Thomas; Lang, Karl-Heinz; Löhe, Detlef:

Residual Stress Sensitivity of Case-Hardened Notched Specimen

In: V.Schulze, A.Niku-Lari (Eds.) Shot Peening and other Mechanical Surface Treatments; Prod. 9th Int. Conf. On Shot Peening (ICSP9), Technology Transfer Series, IITT International, Noisy-le-Grand, France (2005) S. 235 - 240

 

Horsch, Christoph; Schulze, Volker; Löhe, Detlef:

Deburring and Surface Conditioning of Micro Milled Structures by Abrasive and Non-Abrasive Micro Peening

In: V.Schulze, A.Niku-Lari (Eds.) Shot Peening and other Mechanical Surface Treatments; Prod. 9th Int. Conf. On Shot Peening (ICSP9), Technology Transfer Series, IITT International, Noisy-le-Grand, France (2005) S. 191 - 196

 

Lütjens, J.; Heuer, V.; König, F.; Lübben, Th.; Schulze, Volker; Trapp, Nicolas:

Determination of input data for the simulation of case hardening

In: (H.-W. Zoch, Th. Lübben eds.)Proceedings 1st Int. Conf. On Distortion Engineering, Bremen, 2005, S. 269 - 279

 

Franz, Clemens; Lübben, Th.; Lütjens, J.; Streicher, F.; Trapp, Nicolas; Vogel, M:

Case Hardening simulation of Complex Components by Use of Abstraction

In: (H.-W. Zoch, Th. Lübben eds.)Proceedings 1st Int. Conf. On Distortion Engineering, Bremen, 2005, S. 281 - 288

 

Trapp, Nicolas; Fiderer, M.; Lütjens, J.; Ehlers, Martin; Schulze, Volker:

Simulation of case hardening of complex components by use of a constuction kit

In: (H.-W. Zoch, Th. Lübben eds.)Proceedings 1st Int. Conf. On Distortion Engineering, Bremen, 2005, S. 289 - 296

 

Weidenmann, Kay A.; Schomäcker, M.; Kerscher, Eberhard; Löhe, Detlef; Kleiner, Matthias:

Composite Extrusion of Aluminium Matrix Specimens Reinforced with Continuous Ceramics Fibres

Light Metal Age, October 2005, S. 6 - 10

 

Miokovič, Tatjana; Schulze, Volker; Vöhringer, Otmar; Löhe, Detlef:

Auswirkung zyklischer Temperaturänderungen beim Laserstrahlhärten auf den Randschichtzustand von vergütetem 42CrMo4

HTM Zeitschrift für Werkstoffe Wärmebehandlung Fertigung 60 (2005) 3, S. 142 - 149

 

Kotschenreuther, Jan;Delonnoy, Lionel; Hochrainer, Thomas; Weber, Matthias; Schmidt, Jürgen; Fleischer, J.; Schulze, Volker; Löhe, Detlef; Gumbsch, Peter:

Modellierung und experimentelle Untersuchungen von Größeneffekten beim Stirndrehen von 90MnCrV8 im vergüteten Zustand

In: Prozessskalierung (Hrsg.: F. Vollertsen), Strahltechnik, Band 27, BIAS, S. 219 - 239

 

Schulze, Volker:

Stability of surface changes induced by mechanical surface treatments

In: Proc. Of the 9th Int. Conf. On Shot Peening, 6.-9. Sept. 2005, (Ed.: V.Schulze, A.Niku-Lari), Technology Transfer Series, S. 420 - 428

 

Merkel, Jens; Schulze, Volker; Vöhringer, Otmar:

The effects of shot peening and deep rolling on the surface layer and the mechanical properties of sinterer iron

In: Proc. Of the 9th Int. Conf. On Shot Peening, 6.-9. Sept. 2005, (Ed.: V.Schulze, A.Niku-Lari), Technology Transfer Series, S. 241 - 246

 

Klemenz, Manuel; Hochrainer, Thomas; Delonnoy, L.; Schulze, Volker; Vöhringer, Otmar; Gumbsch, Peter:

Similarity rules for the shot peening process based on finite elements simulations

In: Proc. Of the 9th Int. Conf. On Shot Peening, 6.-9. Sept. 2005, (Ed.: V.Schulze, A.Niku-Lari), Technology Transfer Series, S. 94 - 99

 

Löhe, Detlef; Beck, Tilmann:

Mikro-Urformen: Der Sonderforschungsbereich 499

Industrie Management 21 (2005) 6, S. 21 - 24

 

Weidenmann, Kay A.; Fleck, Claudia; Schulze, Volker; Löhe, Detlef:

Materials Selection Process for Compound-Extruded Aluminium Matrix Composites

Advanced Engineering Materials 2005, 7, No. 12, S. 1150 - 1155

 

Weidenmann, Kay A.; Kerscher, Eberhard; Schulze, Volker; Löhe, Detlef:

Grenzflächen in Verbundstrangpressprofilen auf Aluminiumbasis mit verschiedenen Verstärkungselementen

Prakt: Met. Sonderband 37 (2005) S. 131 - 136

 

Weidenmann, Kay A.; Schulze, Volker; Löhe, Detlef; Fleck, Claudia:

Grenzflächencharakterisierung in drahtverstärkten Verbundstrangpressprofilen mit Aluminiummatrix

Verbundwerkstoffe und Werkstoffverbunde, DGM-Matinfo, 2005, S. 45 - 50

 

Raouafi, Naceur; Schulze, Volker; Müller, Hermann; Löhe, Detlef:

Maß- und Formänderungen von Stahlquadern mit unterschiedlichen Aussparungen beim Härten in Öl und Wasser

HTM Z. Werkst. Wärmebeh. Fertigung 60 (2005) 6, S. 304 - 310

 

Schwarzer, Jochen; Rostek, K.; Beck, Tilmann; Vöhringer, Otmar:

Modelling the stress state of a thermal barrier coating system at high temperatures

Zeitschrift für Metallkunde

96 (2005) 7, S. 718 - 724

 

Miokovič, Tatjana; Schulze, Volker; Löhe, Detlef; Vöhringer, Otmar:

Influence of heating rate, cooling rate and numbers of pulses on the microstructure of AISI 4140 after short-time-hardening

Int. J. Materials and Product Technology, Vol.24, Nos. 1-4, 2005, S. 207 - 223

 

Kasanická, Barbora; Horsch, Christoph; Schulze, Volker; Löhe, Detlef:

Analysis of Residual Stresses of Micro Milled and Two-Step Micro Peened Structures

In: HASYLAB Annual Report 2005 [online], erhältlich im Internet unter:

www-hasylab.desy.de/science/annual_reports/2005_report/index.html

 

Sonnweber-Ribic, P.; Wanner, Alexander; Roser, M.; Weingart, D.; Arzt, Edward:

Fatigue failure of titanium implants for mandibular reconstruction

Zeitschrift für Metallkunde 96 (2005), S. 894 - 901

 

Mohrdieck, C.; Wanner, Alexander; Roos, W.; Roos, A.; Roth, A.; Sackmann, E.; Spatz, J. P.; Arzt, Edward:

A Theoretical Description of Elastic Pillar Substrares in Biophysical Experiments

ChemPhysChem 6 (2005), S. 1492 - 1498

 

Gebert, Jörg-Martin; Wanner, Alexander:

Intrinsische Risse und Poren in CVI-CFC-Laminatwerkstoffen

ceramic forum international (cfi) / Berichte der DKG 82 (2005), S. 55 - 60

 

Nejma, Rachid; Lang, Karl-Heinz; Löhe, Detlef:

Dynamische und zyklische Untersuchungen an keramischen Werkstoffen - Erste Einsatzerfahrungen mit einem neuartigen elektromagnetischen Antriebssystem

Werkstoffprüfung 2005, Deutscher Verband für Materialforschung und Prüfung, Berlin, ISSN-1861-8154 (2005), S. 233 - 238

 

Seyedi, Scheida; Lang, Karl-Heinz; Vöhringer, Otmar; Löhe, Detlef:

Verformungs- und Versagensverhalten einsatzgehärteter hochdichter Sinterstähle

FKM Forschungsheft Nr. 288, Forschungskuratorium Maschinenbau, Frankfurt am Main (2005)

 

Luft, Jochen; Beck, Tilmann; Löhe, Detlef:

Lifetime and Damage Behaviour of a Cast Aluminium Alloy under TMF and Superimposed TMF/HCF Loading

Proc. 11th Int. Conf. On Fracture, Turin 2005, CD-ROM edition

 

Henne, Ingo; Beck, Tilmann; Löhe, Detlef:

Modellierung der Schädigungsentwicklung thermisch-mechanisch hochbeanspruchter Motorbauteile und Ermittlung geeigneter Werkstoffkennwerte

Zwischenbericht zum FVV-Forschungsvorhaben Nr. 819, FVV-Forschungsheft R528 (2005), Forschungsvereinigung Verbrennungskraftmaschinen, Frankfurt/Main, S. 285 - 308

 

Luft, Jochen; Beck, Tilmann; Löhe, Detlef:

Weiterentwicklung des Al-Leichtbaus für motorische Hochleistungskomponenten mit Hilfe einer neuen TMF/HCF-Methode

Abschlussbericht zum BMBF-Verbundprojekt 03N3095, online verfügbar unter:

tws.gbv.de/DB=2.36/CMD

 

Beck, Tilmann; Luft, Jochen; Löhe, Detlef:

Lebesdauer von Aluminiumzylinderkopflegierungen bei überlagerten niederfrequenten thermischen und höherfrequenten mechanischen Ermüdungsbeanspruchungen

U.Brill, A.Velji (Hrsg.): Der Konflikt zwischen Thermodynamik und Mechanik in der Motorentwicklung, Haus der Technik Fachbuch 63 (2005), Expert-Verlag, Renningen, S. 64 - 73

 

Ermel, Ralf; Beck, Tilmann; Kerscher, Eberhard:

Influence of Heat Treatment and Matrix Microstructure on the Mechanical Properties of CFC out of Chemical Vapour Infiltration

Proc. Carbon 2005, Gyeongju, Korea, 3.-7.07.2005, CD-ROM edition

 

Ermel, Ralf; Beck, Tilmann; Kerscher, Eberhard; Fleck, Claudia:

Einfluss von Matrixmikrostruktur und Faser-Matrix Grenzflächen auf das Versagensverhalten von CFC-Werkstoffen aus chemischer Gasphaseninfiltration

In: M.Schlimmer: Verbundwerkstoffe und Werkstoffverbunde, Werkstoffinformationsgesellschaft GmbH (2005), S. 139 - 144

Veröffentlichungen 2004

Nejma, Rachid; Lang, Karl-Heinz; Löhe, Detlef:

Lifetime behaviour of alumina at room and higher temperature

In: Proceedings of the 5th Int. Conference on Low Cycle Fatigue LCF 5, ed.:P.D. Portella, H.; Sehitoglu, K. Hatanaka, DVM (2004), S. 101 - 106

 

Löhe, Detlef; Beck, Tilmann; Lang, Karl-Heinz:

Important aspects of cyclic deformation, damage and lifetime behaviour in thermomechanical fatigue of engineering alloys

In: Proceedings of the 5th Int. Conference on Low Cycle Fatigue LCF 5, ed.:P.D. Portella,H.; Sehitoglu, K. Hatanaka,DVM (2004), S. 161 - 175

 

Luft, Jochen; Beck, Tilmann; Löhe, Detlef:

Thermal-mechanical fatigue behavior of the cast aluminium alloy AlSi7Mg

In: Proceedings of the 5th Int. Conference on Low Cycle Fatigue LCF 5, ed.:P.D. Portella,H.; Sehitoglu, K. Hatanaka,DVM (2004), S. 219 - 224

 

Auhorn, Markus; Beck, Tilmann; Schulze, Volker; Löhe, Detlef:

Determination of mechanical properties of slip cast, micro powder injection moulded and microcast high aspect ratio microspecimens

Microsystem Technologies 10 (2004) S. 489 - 492

 

Nejma, Rachid; Lang, Karl-Heinz; Löhe, Detlef:

Influence of the temperature on the strength and the subcritical crack growth rate of alumina

Materials Science and Engineering A387 - 389 (2004) S. 832 - 836

 

Franz, Clemens; Besserdich, Gerhard; Schulze, Volker; Müller, Hermann; Löhe, Detlef:

Influence of transformation plasticity on residual stresses and distotions due to the heat treatment of steels with different carbon contents

Proceedings of the 2nd ICTPMCS, Journal de Physique 4 France 120 (2004) S. 481 - 488

 

Miokovic; Tatjana; Schwarzer, Jochen; Schulze, Volker; Vöhringer, Otmar; Löhe, Detlef:

Description of short time phase transformations during the heating of steels based on high-rate experimental data

Proceedings of the 2nd ICTPMCS, Journal de Physique 4 France 120 (2004) S. 591 - 598

 

Schwarzer, Jochen; Löhe, Detlef; Vöhringer, Otmar:

Influence of the TGO creep behavior on delamination stress development in thermal barrier coating systems

Materials Science and Engineering A387 - 389 (2004) S. 692 - 695

 

Ermel, Ralf; Beck, Tilmann; Vöhringer, Otmar:

Mechanical properties and microstructures of carbon fibre reinforced carbon materials produced by chemical vapour infiltration

Materials Science and Engineering A387 - 389 (2004) S. 845 - 851

 

Löhe, Detlef; Schulze, Volker; Fleck, Claudia; Weidenmann, K.A.:

Verbundstranggepresste Aluminiummatrixverbunde - Werkstoffauswahl und Charakterisierung ausgewählter Metall-Metall-Systeme

Aluminium, 80. Jahrgang 2004, 12, S. 1374 - 1378

 

Schulze, Volker; Löhe, Detlef; Barreiro, Pablo:

Einfluss kombinierter Nd:YAG- und Hochleistungsdioden-Laserstrahlschweißprozesse auf die mechanischen Eigenschaften von Al6060 bei quasistatischer Beanspruchung

Aluminium, 80. Jahrgang 2004, 12, S. 1392 - 1396

 

Gronych, D.; Auhorn, Markus; Beck, Tilmann; Schulze, Volker; Löhe, Detlef:

Influence of surface defects and edge geometry on the bending strength of slip-cast ZrO2 microspecimens

Zeitschrift für Metallkunde 95 (2004) 6, S. 551 - 558

 

Beck, Tilmann; Schneider, J.; Schulze, Volker:

Characterisation and testing of micro specimen

Microsystem Technologies 10 (2004) S. 227 - 232

 

Kasanická, Barbora; Schulze, Volker; Löhe, Detlef:

Analysis of Residual stresses in Moulded ZrO2 Micro Specimens

In: HASYLAB Annual Report 2004

www-hasylab.desy.de/science/annual_reports/2004_report/index.html

 

Stencio, A.; Krug, Thomas; Tobie, T.; Oster, P.; Lang, Karl-Heinz; Höhn, B.-R.; Löhe, Detlef:

Eigenspannung Zahnfuß-Eigenspannungseinfluss auf die Zahnfußtragfähigkeit kleinmoduliger Zahnräder

FVA Forschungsheft Nr. 745, Forschungsvereinigung Antriebstechnik e. V., Frankfurt (2004)

 

Egly, Tobias; Lang, Karl-Heinz; Löhe, Detlef:

Kontaktermüdung im Rad-Schiene-System

Werkstoffprüfung 2004, MAT-INFO Werkstoff-Informationsges., Frankfurt a. M., ISBN 3-88355-337-9 (2004) S. 175 - 181

 

Wanner, Alexander:

Wundermetall Titan

Kultur & Technik, Heft 2004/1, S. 16 - 20

 

Böhm, J.; Gruber, P.; Spolenak, R.; Stierle, A.; Wanner, Alexander; Arzt, Edward:

Tensile Testing of Ultrathin Polycrystalline Films: A New Synchrotron-based Technique

Review of Scientific Instruments 75 (4), 2004, S. 1110 - 1119

 

Wanner, Alexander; Garces, G.:

Creep of Multidirectionally Reinforced Composites

Phil. Mag. A. 84, (2004) S. 3019 - 3038

 

Böhm, J.; Gruber, P.; Spolenak, R.; Wanner, Alexander; Arzt, Edward:

A New Synchrotron-based Technique for Measuring Stresses in Ultrathin Metallic Films

Mater. Res. Soc. Sympos. Proc. 821, 2004, P1.61-P1.6.6

 

Gruber, P.; Böhm, J.; Wanner, Alexander; Sauter, L.; Spolenak, R.; Arzt, Edward

Size Effect on Crack Formation in Cu/Ta and Ta/Cu/Ta Thin Film Systems

Mater. Res. Soc. Sympos. Proc. 821, 2004, P2.7.1-P2.7.7

 

Erbacher, Thomas; Beck, Tilmann; Vöhringer, Otmar:

Eigenspannung und Schädigungsentwicklung in friktionsbeanspruchten Ingenieurkeramiken

DGM-Werkstoffwoche, 21,.23.09.2004, www.materialsweek.org

 

Erbacher, Thomas; Beck, Tilmann; Vöhringer, Otmar:

Schädigungsverhalten von Al²O³-Keramiken bei trockener Friktions- und thermischer Ermüdungsbeanspruchung - Experiment und Simulation

DKG-Jahrestagung, Karlsruhe, 11.-13.10.2004, DKG e. V. Köln (2004), 16

 

Hähner, P.; Beck, Tilmann:

Thermo-mechanical fatigue - the route to standardisation (TMF-STANDARD)

Proc. EFC-Workshop "Novel Approaches to the Improvement of High Temperature Corrosion Resistance", Frankfurt am Main, 27.-29.10.2004, DECHEMA e. V. (2004), 33

 

 

Ermel, Ralf; Beck, Tilmann; Fleck, Claudia:

Influence of Matrix Microstructure and Test Conditions on the Pseudoductile Failure of CVI-CFC

Proc. 15th European Conference on Fracture, Stockholme 2004, CD-ROM Edition and www.ecfl15.org

Veröffentlichungen 2001

Auhorn, Markus; Beck, Tilmann; Schulze, Volker; Löhe, Detlef:

Mechanical Testing of Specimens with High Aspect Ratios Produced by Micro-Casting and Micro-Powder-Injection-Molding.

In: Proc. HARMST 01 (2002), S. 153 - 154

 

Beck, Tilmann; Denne, Bernhard; Lang, Karl-Heinz; Löhe, Detlef:

Torsionsermüdungsprüfmaschine mit AC-Servomotor.

Materialprüfung 43 (2001), 7-8, S. 283-287

 

Beck, Tilmann; Lang, Karl-Heinz; Löhe, Detlef:

Thermal-Mechanical Fatigue Behaviour of Cast Aluminium Alloys for Cylinder Heads Reinforced with 15 Vol.-% Discontinous Al2O3 (Saffil) Fibers.

Materials Science and Engineering A319-321 (2001) S. 662 - 666

 

Beck, Tilmann; Löhe, Detlef; Lang, Karl-Heinz:

Fatigue Behaviour of an Aluminium Foam Sandwich Beam under Alternating Bending.

Cellular Metals and Foaming Technology, J. Banhart, M. Ashby, N. Fleck (Eds.), MIT Publishing, Bremen (2001), S. 305 - 310

 

Beck, Tilmann; Lang, Karl-Heinz; Vöhringer, Otmar; Löhe, Detlef:

Experimental Analysis of the Interaction of "Hot" and "Cold" Volume Elements during Thermal Fatigue of a Cooled Component made from AISI 316 L Steel.

Zeitschrift für Metallkunde 92 (2001), S. 875 - 881

 

Biesinger, Frank; Söhner, Jörg; Schulze, Volker; Vöhringer, Otmar; Weule, Hartmut:

Aspects of Materials Science and Production Engineering at High-Speed-Cutting Processes and their Finite-Element Simulation.

In: Metal Cutting and High Speed Machining (Eds. D. Dudzinski, A. Molinari, H. Schulz); Ecole Nationale D'Ingenieurs de Metz (2001), S. 67 - 71

 

Biesinger, Frank; Thiel, M.; Schulze, Volker; Vöhringer, Otmar; Krempe, Manfred; Wendt, Ulrich:

Characterization of Surface and Subsurface Regions of HSC-milled Steel.

In: Scientific Fundamentals of HSC (Ed. by H. Schulz). Carl Hanser Verlag, München, 2001, S. 137 - 149

 

Denne, Bernhard; Lang, Karl-Heinz; Löhe, Detlef:

Verformungs- und Lebensdauerverhalten des Schienenstahls UIC 60 900 A.

DET Die Eisenbahntechnik, Zeitschrift für Eisenbahnwesen und Verkehrstechnik, Heft 2, 2001, S. 67 - 77

 

Erbacher, Thomas; Beck, Tilmann; Vöhringer, Otmar:

Prüfung von Al2O3-Keramiken für Kupplungsscheiben unter Friktionsbelastung.

Werkstoffprüfung-Schadenanalyse und Schadenvermeidung, G. Lange und M. Pohl (Eds.), Wiley-VCH, Weinheim (2001) S. 104-109

 

Erbacher, Thomas; Beck, Tilmann; Vöhringer, Otmar:

Experimentelle und numerische Analyse des Schädigungsverhaltens hochbeanspruchter Friktionsflächen aus Al2O3-Keramik.

In: Hochbeanspruchte Gleit- und Friktionssysteme auf Basis ingenieurkeramischer Werkstoffe, Statuskolloquium am 22.01.2002 des DFG-Sonderforschungsbereichs 483, Universität Karlsruhe (TH), Hrsg.: K.-H. Zum Gahr, J. Schneider, Rufdruck, Dezember 2001, S. 165 - 176

 

Gerber, Andreas; Schulze, Volker; Löhe, Detlef:

Automated Welding of Extruded Profiles and Sheets of Aluminium Alloys for Car Bodies.

In: X.-S. Yi, O. Hahn (eds.): Proc. Ultralight Symposium Beijing, DVS-Verlag 2001, DVS-Berichte Band 218, ISBN 3-87155-676-9, S. 89 - 99

 

Hoffmann, Bertram; Vöhringer, Otmar; Macherauch, Eckard:

Effect of Compressive Plastic Deformation on Mean Lattice Strains, Dislocation Densities and Flow Stresses of Martensitically Hardened Steels.

Materials Science Engineering 319 - 321 (2001), S. 299 - 303

 

Menig, Rainer; Wick, Andreas; Schulze, Volker; Vöhringer, Otmar:

Neuere Untersuchungen zum Eigenspannungsabbau von Stählen.

In: H. Pries, Th. Nitschke-Pagel (Hrsg.): Forschungsberichte des Instituts für Schweißtechnik, TU Braunschweig, Festigkeit von Schweißverbindungen, ISBN 3-8265-8598-4, Aachen, 2001, S. 43 - 59

 

Menig, Rainer; Meyers, Marc H.; Meyers, Marc A.; Vecchio, Kenneth:

Quasi-static and dynamic mechanical response of Strombus gigas (conch) shells.

Materials Science and Engineering A297 (2001), S. 203 - 211

 

Menig, Rainer; Pintschovius, Lothar; Schulze, Volker; Vöhringer, Otmar:

Depth profiles of macro residual stresses in thin shot peened steel plates determined by X-ray and neutron diffraction.

Scripta Materialia 45 (2001), S. 977 - 983

 

Meyers, Marc A.; Vöhringer, Otmar; Lubarda, V. A.:

The onset of twinning in metals: a constitutive description.

Acta Materialia 49 (2001), S. 4025 - 4039

 

Moalla, Mourad; Lang, Karl-Heinz; Löhe, Detlef:

Effect of superimposed high cycle fatigue loadings on the out-of-phase thermal-mechanical fatigue behaviour of CoCr22Ni22W14.

Materials Science and Engineering A319-321 (2001) S. 647 - 651

 

Nejma, Rachid; Lang, Karl-Heinz; Löhe, Detlef:

Ermüdungsverhalten von thermisch und mechanisch beanspruchter Al2O3-Keramik.

In: Hochbeanspruchte Gleit- und Friktionssysteme auf Basis ingenieurkeramischer Werkstoffe, Statuskolloquium am 22.01.2002 des DFG-Sonderforschungsbereichs 483, Universität Karlsruhe (TH), Hrsg.: K.-H. Zum Gahr, J. Schneider, Rufdruck, Dezember 2001, S. 177 - 187

 

Obergfell, Katja; Schulze, Volker; Löhe, Detlef; Vöhringer, Otmar:

Application of X-Ray Diffraction Analysis on Microstructural Investigations of Laser-Hardened Steel Surfaces.

Zeitschrift für Metallkunde 92/2001, S. 265 - 269

 

Obergfell, Katja; Schulze, Volker; Löhe, Detlef; Vöhringer, Otmar:

Einfluss der Pulsfrequenz auf das temperaturkontrollierte Laserstrahlhärten von Stählen.

Härterei-Techn. Mitteilungen 56 (2001), S. 353 - 358

 

Peichl, Andrea; Beck, Tilmann; Vöhringer, Otmar:

Behaviour of an EB-PVD Thermal Barrier Coating System under TMF Loading.

Materials Week 2000, München, Symposium C2 - Materials and Coating Development for Turbomachinery, Session - Thermal Barrier Coatings I, im Internet unter www.materialsweek.org/proceedings verfügbar.

 

Pintschovius, Lothar; Kämpfe, Andreas; Eigenmann, Bernd; Löhe, Detlef:

Residual Stress Analysis in Actively Brazed Joints of Aluminium Nitride and Copper Using Neutron and X-Ray Diffraction.

Zeitschrift für Metallkunde 92/2001, S. 275 - 280

 

Pintschovius, Lothar; Kämpfe, Andreas; Eigenmann, Bernd; Wick, Andreas:

Determination of Steep Stress Gradients at Surfaces or Interfaces by Means of Neutron Diffraction.

Journal of Neutron Research, Vol. 9 (2001) OPA, S. 181 - 185

 

Schmidt, Uli T.; Löhe, Detlef; Vöhringer, Otmar:

High Temperature Deformation of Combustion Chamber Materials in Different Component Conditions.

Materials Science Engineering, 319 - 321 (2001), S. 760 - 764

 

Schöfer, Jörg; Rehbein, Peter; Stolz, U.; Löhe, Detlef; Zum Gahr, Karl-Heinz:

Formation of tribochemical films and white layers on self-mated bearing steel surfaces in boundary lubricated sliding contact.

WEAR 248 (2001) Elsevier Science, S. 7 - 15

 

Scholtes, Berthold; Vöhringer, Otmar:

Mechanical Surface Treatment.

Encyclopedia of Materials: Science and Technology (Eds. K. H. J. Bushow, R. W. Cahn, M. C. Flemings, B. Ilschner, E. J. Kramer, S. Mahajan); ISBN 0-08-0431526, Elsevier Science Ltd., 2001, S. 5253 - 5262

 

Schulze, Volker; Vöhringer, Otmar:

Plastic Deformation: Constitutive Description.

Encyclopedia of Materials: Science and Technology (Eds. K. H. J. Bushow, R. W. Cahn, M. C. Flemings, B. Ilschner, E. J. Kramer, S. Mahajan); ISBN 0-08-0431526, Elsevier Science Ltd., 2001, S.7050 - 7064

 

Schulze, Volker; Hornung, A.; Dahmen, Nicolaus; Hierl, F.; Türk, M.; Piotter, V.:

Entbinderung pulverspritzgegossener Bauteile mit überkritischem Kohlendioxid.

In: N. Dahmen, V. Piotter, F. Hierl, M. Roelse, Überkritische Fluide zur Behandlung und Herstellung komplexer Werkstoffe und Oberflächenstrukturen, Wissenschaftliche Berichte des Forschungszentrums Karlsruhe, FZKA 6585, ISSN 0947-8620, Karlsruhe, 2001, S. 34 - 64

 

Söhner, Jörg; Weule, Hartmut; Biesinger, Frank; Schulze, Volker; Vöhringer, Otmar:

Examinations and 3 D-Simulations of HSC face milling process.

Fourth CIRP International Workshop "Modelling of machining operations" 17./18.08.2001 (Ed. by C. A. van Luttervelt); Technological University Delft, 2001, ISBN 90-370-0187-4, S. 111 - 115