Dr.-Ing. Johannes Schneider

Publikationen


2023
Waviness Affects Friction and Abrasive Wear
Li, Y.; Garabedian, N.; Schneider, J.; Greiner, C.
2023. Tribology Letters, 71 (2), Art.-Nr.: 64. doi:10.1007/s11249-023-01736-1
Establishment and Calibration of a Digital Twin to Replicate the Friction Behaviour of a Pin-on-Disk Tribometer
Hansen, E.; Vaitkunaite, G.; Schneider, J.; Gumbsch, P.; Frohnapfel, B.
2023. Lubricants, 11 (2), Art.-Nr.: 75. doi:10.3390/lubricants11020075
2022
Generating FAIR research data in experimental tribology
Garabedian, N. T.; Schreiber, P. J.; Brandt, N.; Zschumme, P.; Blatter, I. L.; Dollmann, A.; Haug, C.; Kümmel, D.; Li, Y.; Meyer, F.; Morstein, C. E.; Rau, J. S.; Weber, M.; Schneider, J.; Gumbsch, P.; Selzer, M.; Greiner, C.
2022. Scientific Data, 9 (1), Art.Nr. 315. doi:10.1038/s41597-022-01429-9
Dislocation-mediated and twinning-induced plasticity of CoCrFeMnNi in varying tribological loading scenarios
Dollmann, A.; Kauffmann, A.; Heilmaier, M.; Srinivasan Tirunilai, A.; Mantha, L. S.; Kübel, C.; Eder, S. J.; Schneider, J.; Greiner, C.
2022. Journal of Materials Science, 57, 17448–17461. doi:10.1007/s10853-022-07661-3
Tribological mechanisms of slurry abrasive wear
Li, Y.; Schreiber, P.; Schneider, J.; Greiner, C.
2022. Friction, 11 (6), 1079–1093. doi:10.1007/s40544-022-0654-1
Determination of constitutive friction laws appropriate for simulation of cutting processes
Schulze, V.; Bleicher, F.; Courbon, C.; Gerstenmeyer, M.; Meier, L.; Philipp, J.; Rech, J.; Schneider, J.; Segebade, E.; Steininger, A.; Wegener, K.
2022. CIRP Journal of Manufacturing Science and Technology, 38, 139–158. doi:10.1016/j.cirpj.2022.04.008
2021
Development of a new topographical parameter set for characterizing textured rough surfaces
Yue, H.; Deng, J.; Schneider, J.
2021. Surface Topography: Metrology and Properties, 9 (3), 035013. doi:10.1088/2051-672X/ac1723
Large characteristic lengths in 3D chiral elastic metamaterials
Frenzel, T.; Hahn, V.; Ziemke, P.; Schneider, J. L. G.; Chen, Y.; Kiefer, P.; Gumbsch, P.; Wegener, M.
2021. Communications materials, 2 (1), Art.Nr. 4. doi:10.1038/s43246-020-00107-w
2020
Additive laser barcode printing on high reflective stainless steel
Mihalev, M. S.; Hardalov, C. M.; Christov, C. G.; Rinke, M.; Leiste, H.; Schneider, J.
2020. Acta polytechnica, 60 (5), 435–439. doi:10.14311/AP.2020.60.0435
Surface engineering of a titanium alloy for tribological applications by nanosecond-pulsed laser
Kümmel, D.; Linsler, D.; Schneider, R.; Schneider, J.
2020. Tribology international, 150, Article no: 106376. doi:10.1016/j.triboint.2020.106376
Influence of Interstitial Oxygen on the Tribology of Ti6Al4V
Kümmel, D.; Schneider, J.; Gumbsch, P.
2020. Tribology letters, 68 (3), Art. Nr.: 96. doi:10.1007/s11249-020-01327-4
2019
Tribological behavior of nanosecond-laser surface textured Ti6Al4V
Kümmel, D.; Hamann-Schroer, M.; Hetzner, H.; Schneider, J.
2019. Wear, 422-423, 261–268. doi:10.1016/j.wear.2019.01.079
2018
Numerical and experimental investigation of texture shape and position in the macroscopic contact
Codrignani, A.; Frohnapfel, B.; Magagnato, F.; Schreiber, P.; Schneider, J.; Gumbsch, P.
2018. Tribology international, 122, 46–57. doi:10.1016/j.triboint.2018.02.001
Experimental and Simulative Modeling of Drilling Processes for the Compensation of Thermal Effects
Bollig, P.; Michna, J.; Faltin, C.; Schneider, J.; Zanger, F.; Schießl, R.; Maas, U.; Schulze, V.
2018. Thermal Effects in Complex Machining Processes. Hrsg.: D. Biermann, F. Hollmann, 145–180, Springer International Publishing. doi:10.1007/978-3-319-57120-1_9
Surface texturing of TiAl6V4 using cutting tools in reverse
Segebade, E.; Kümmel, D.; Zanger, F.; Schneider, J.; Schulze, V.
2018. Procedia manufacturing, 18, 97–103. doi:10.1016/j.promfg.2018.11.013
Influence of cutting edge asymmetry on grain refinement of Ti6Al4V
Segebade, E.; Kümmel, D.; Zanger, F.; Schneider, J.; Schulze, V.
2018. Procedia CIRP, 71, 232–237. doi:10.1016/j.procir.2018.05.065
Friction reduction through biologically inspired scale-like laser surface textures
Schneider, J.; Djamiykov, V.; Greiner, C.
2018. Beilstein journal of nanotechnology, 9, 2561–2572. doi:10.3762/bjnano.9.238
Tribological Effects in and by Metal Cutting
Segebade, E.; Schneider, J.; Schulze, V.
2018. 8th International Conference on Tribology in Manufacturing Processes and Joining by Plastic Deformation, ICTMP 2018; Elsinore; Denmark; 24 June 2018 through 26 June 2018. Ed.: N. Bay, 3–24, Trans Tech Publications. doi:10.4028/www.scientific.net/KEM.767.3
2017
Microstructure, mechanical properties and friction behavior of magnetron-sputtered V-C coatings
Stoyanov, P.; Schneider, J.; Rinke, M.; Ulrich, S.; Nold, E.; Dienwiebel, M.; Stüber, M.
2017. Surface and coatings technology, 321, 366–377. doi:10.1016/j.surfcoat.2017.04.050
2016
Tribological Performance of Aligned Silicon Nitride Ceramics under Isooctane-Lubricated Oscillating Sliding Conditions
Schneider, J.; Miranzo, P.; Isabel Osendi, M.; Belmonte, M.
2016. Journal of the American Ceramic Society, 99 (1), 241–248. doi:10.1111/jace.13805
Chronology of the microstructure evolution for pearlitic steel under unidirectional tribological loading
Wolff, K.; Liu, Z.; Braun, D.; Schneider, J.; Greiner, C.
2016. Tribology international, 102, 540–545. doi:10.1016/j.triboint.2016.06.016
2015
Study on micro texturing of uncoated cemented carbide cutting tools for wear improvement and built-up edge stabilisation
Kümmel, J.; Braun, D.; Gibmeier, J.; Schneider, J.; Greiner, C.; Schulze, V.; Wanner, A.
2015. Journal of Materials Processing Technology, 215, 62–70. doi:10.1016/j.jmatprotec.2014.07.032
2014
Experimental Analysis of microstructured steel surfaces for wet tribological applications in the low velocity regime
Chlipala, M.; Schneider, J.; Schulze, V.
2014. Conference papers in science, Article ID 387830. doi:10.1155/2015/387830
2013
Influence of cutting parameters, tool coatings and friction on the process heat in cutting processes and phase transformations in workpiece surface layers∗
Schulze, V.; Michna, J.; Zanger, F.; Faltin, C.; Maas, U.; Schneider, J.
2013. HTM - journal of heat treatment and materials, 68 (1), 22–31. doi:10.3139/105.110177
2011
Modelling of cutting induced surface phase transformations considering friction effects
Schulze, V.; Michna, J.; Schneider, J.; Gumbsch, P.
2011. Procedia engineering, 19, 331–336. doi:10.1016/j.proeng.2011.11.121
Veröffentlichungen
Titel Autor Quelle

Tribology Letters, Band online first,
Seiten in press (2012)

Tribology International, Band 55,
Seiten 81-86 (2012)

Geometrische und mikrostrukturelle
Skaleneffekte im ungeschmierten,
einsinnigen Gleitkontakt von keramischen
Werkstoffpaarungen,
Hrsg. Gesellschaft für Tribologie e.V.,
GFT Verlag, Seiten 8/1-8/11 (2011)

Einfluss des fertigungsbedingten
Oberflächenzustandes auf den
Formeinsatzverschleiß beim ?PIM
und das tribologische Verhalten
urgeformter Mikrokomponenten,
Hrsg. O. Kraft, A. Haug, F. Vollertsen,
S. Büttgenbach, KIT Scientific Publishing
Verlag, Seiten 57-64 (2011)

Tribologische Charakterisierung von
Sialon- und Sialon-SiC-Keramiken im
mediengeschmierten, reversierenden
Gleitkontakt,
Hrsg. A. Albers, J. Schneider,
KIT Scientific Publishing Verlag,
Seiten 89-99 (2011)

Proc. SPIE, Band 7921,
Seiten 792108 (2011)

Charakterisierung von Scherfestigkeit
und tribologischem Verhalten lasergefügter
Keramik/Stahl-Verbunde im Hinblick auf
den Einsatz in PKW-Trockenkupplungen,
Hrsg. KIT Scientific Publishing,
Verlag A. Albers, J. Schneider
Seiten 141-150 (2011)

Journal of the American Ceramic Society,
Band 94, Seiten 2542-2548 (2011)

Keramische Komponenten mit
mikrotexturierten Funktionsflächen
für mediengeschmierte Gleitsysteme
Hrsg. A. Albers, J. Schneider
KIT Scientific Publishing Verlag
Seiten 67-77 (2011)

Mikrotexturierte Keramik/Metall-
Tribokontakte in ölgeschmierten
Friktionspaarungen, Hrsg. A. Albers,
J. Schneider, KIT Scientific
Publishing Verlag, Seiten 115-125
(2011)

Tribologie und Schmierungstechnik,
Band 58 [1], (2011)

Microsystem Technologies, Band 17 (2011)

in Proc. „Konstruktion, Werkstoffentwicklung und Schadenanalyse“, Hrsg. M. Pohl, Verlag Stahleisen GmbH, Düsseldorf, Seiten 293 - 298 (2010)

in Proc. "4M 2010 Conference", Hrsg. B. Fillon, C. Khan-Malek, S. Dimov, Research Publishing, Singapore, Seiten 239 - 242 (2010)

in Proc. „Tribologie-Fachtagung 2010“, Deutsche Gesellschaft für Tribologie (GFT), Aachen, 40/1 - 40/10 (2010)

in Proc. „Tribologie-Fachtagung 2010“, Deutsche Gesellschaft für Tribologie (GFT), Aachen, 02/1 - 02/10 (2010)

Tribologie + Schmierungstechnik,
Band 57 [1], Seiten 12-16 (2010)

Tribologie und Schmierungstechnik,
Band 57 [2], Seiten 5 - 10 (2010)

Tribologie und Schmierungstechnik, Band 57 [2], Seiten 5 - 10 (2010)

Tribologie-Fachtagung 2009, Hrsg. Deutsche Gesellschaft für Tribologie, Aachen,
Seiten 42/1 - 42/8 (2009)